Sanyo DVR-S120 Manuel D’Utilisation

32

1.  Turn the TV on and select input from the DVD recorder. (For details 

on operation methods, refer to your TV’s manual.)

2. Press 

SYSTEM MENU  to display the System Menu.

3.  Select “Sound” using 8 or 2, and press 6 once. The setting items 

at "Sound Options" on the right of the screen can now be selected 
using 8 or 2.

4.  Select the item to be changed using 8 or 2, and change the set-

tings.

System Menu

Sound Options

Video

Feature

Language

Recording

Setup

Digital Output

Analog Output

Night Mode

Set output from the digital audio output terminal.
When you press the k button, the selection items 

are displayed. Select digital output using 8 or 2, and 

press the k button.

Off 

Select this when digital audio output is not 
used.

PCM Only  Dolby Digital and MPEG-2 multi-channel 

signals are converted to PCM (Pulse Code 
Modulation). This setting is for receiv-
ers/amplifi ers without digital multi-channel 
sound decoders. DTS is not converted into 
PCM. (Sound does not output.)

All 

Dolby Digital and DTS signals are fed 
unaltered to the digital output. MPEG-2 
multi-channel signals are converted to 
PCM (Pulse Code Modulation). This set-
ting is for receivers/amplifi ers with digital 
multi-channel sound decoders.

Set output from the analogue audio output terminal 
(L/R AUDIO OUT).
When you press the k button, the selection items 

are displayed. Select analogue output using 8 or 2, 

and press the k button.

Stereo 

For devices without DolbySurround or 
TruSurround. Use this setting if the DVD 
recorder is connected only to a stereo TV 
set.

Surround   Dolby Digital and MPEG-2 multi-channel 

are mixed down to a DOLBY surround-
compatible two-channel output signal. For 
devices with Dolby Surround Pro Logic 
decoder.

Night mode optimises the sound for playback at low 
volume. You are therefore less likely to disturb your 
neighbours. This only works for Dolby Digital audio on 
DVD video discs. This option can be selected if required. 
Night Mode works only when analog output.
To use this feature, press the k button to select it. 

Each press of k selects or deselects this setting.

- 

When you press 4 , other items in the System Menu can be selected. 

Set other items as necessary.

5.  To end setting, press SYSTEM MENU.

1.  Turn the TV on and select input from the DVD recorder. (For details 

on operation methods, refer to your TV’s manual.)

2. Press 

SYSTEM MENU  to display the System Menu.

3. Select 

“Feature” 

using 

8 or 2, and press 6 once. The setting items 

at "Feature Options" on the right of the screen can now be selected 
using 8 or 2.

4.  Select the item to be changed using 8 or 2, and change the set-

tings.

System Menu

Feature Options

Video

Sound

Language

Recording

Setup

Access Control

Press OK

Status Display

Resume

Auto Standby

Clock Display: Off

PBC Enable

Parental Level Control
Accessing of DVD discs can be controlled.
For details, see “Parental Level Control” on page 34.

Along with the on-screen menu, the OSD (On Screen 
Display) also displays information on the current operat-
ing status (counter, playback, recording, TV channel, 
etc.) on the TV screen. By default, this would be off, to 
see the information about the operating status, check 
the “Status Display” box. This appears in every selected 
mode for a few seconds and disappears.
To use this feature, press the k button to select it. 

Each press of k selects or deselects this setting.

If playback of a pre-recorded DVD video disc is inter-
rupted (rOPEN/CLOSE), when the disc is reloaded 

(disc is started), playback starts at the precise location 
where it stopped. This applies not only to the current 
disc but to the last 20 discs played. This feature can 
be switched off if not required.
To use this feature, press the k button to select it. 

Each press of k selects or deselects this setting.

To set whether or not to set the standby mode when 
no operations have been performed for 10 minutes. 
When no DVD recorder operation has occured for 
10 minutes after e(STOP) button is pressed , this 

unit will  go to standby mode. This function works CD 
media(Audio, MP3 or JPEG) only.
To use this feature, press the k button to select it. 

Each press of k selects or deselects this setting.

To save power, you can switch off the clock display on 
the DVD recorder. Programmed (TIMER) recordings 
will still take place.
If the recorder is switched off (button o), the clock 

display is also switched off when checked.
If the recorder is switched off (button o), the 

clock display is visible when unchecked.
To use this feature, press the k button to select it. 

Each press of k selects or deselects this setting.

- 

When you press 4, other items in the System Menu can be selected. 

Set other items as necessary.

5.  To end setting, press SYSTEM MENU.

DVR_S120_INS_MANUAL.indd   32

DVR_S120_INS_MANUAL.indd   32

5/19/2005   11:54:27 AM

5/19/2005   11:54:27 AM