Emerson DECT 6.0 EM6113 Manuel D’Utilisation

8

CAUTION: To reduce the risk of personal injury, fire, or damage use only the 

EM6113 power adaptor listed in the user’s guide.  This power adaptor is 

intended to be correctly orientated in a vertical or floor mount position.

5. Allow the phone to charge for 16 hours prior to first use.  If you don't properly charge

    the phone, battery performance is compromised 

The integrated digital answering machine offers a total recording time of up to 11 minutes 

for outgoing and incoming messages. Self recorded memos are treated like messages.

You can operate the answering machine at the base station. An internal voice will give 

you advice. You can switch the language from German to french.  Using a telephone 

with tone dialling (DTMF) you have also a PIN protected remote access.
You can select between two mode:

- Answer and record

- Answer only
A standard announcement is already saved for every operating type at the delivery stage.  

Therefore the answering machine is immediately operational.  At “Answer and record” and 

reaching of the maximum recording capacity the device will automatically switch to the 

operating type “Answer only”.

If the answering machine is turned off the announcement for the operating type “Answer 

only” will be played after approx. 10 rings.

When playback messages the voice will give you information about day and time of the 

relevant call (only when date and time were set correctly). 

The display gives you information:

XX

Digits steadily on: Number of old (already heard) messages  Flashing digits:

                     Number of new messages.

FL

TAM memory is full.

Press briefly          . 

The number of rings after which the answering machine will answer calls can be set from 

2 - 9 and tS (toll saver).  The standard setting is 5 rings.  In toll saver mode, the machine 

will answer after 5 rings if there are no new messages, and after 2 rings if there are new 

messages.  If there are no new messages and you call your machine to check your 

messages remotely, you can hang up after the 2nd ring.  You do not need to pay 

connection fees and you know that you do not have any new messages.
Press briefly           to check the setting.
Press and HOLD           to enter setting mode.  Use the          and           to set the number 

of rings.
Press          for confirmation.

      

15

Press the          button.  Select and entry.  Press the          button repeatedly, to show the 

telephone number and the melody.  
Press the             button.  The displayed telephone number is being dialed.

   The handset is in idle state
Press the          button.  
Press the          button.  Select EDIT ENTRY, using the          or the         button, and press 
the        button.  Edit name if necessary and press the         button.  Edit number if 
necessary and press the            button.  Change melody and press the          button.  
Press the         button to delete the last character or press and HOLD the         button to 
delete the whole entry.  You can enter a dialing pause (approximately 3 seconds) by 
pressing the          button.
Press the           button again to store the edited entry.

When the desired entry is displayed, press the          button.  Select DELETE ENTRY          

or DELETE ALL if necessary and press the         button.  The entry or all entries will be 

deleted.

CID

◄

/ 

/ 

You can store up to 50 entries in the phonebook.

   The handset in the idle state.
Press the         button.  The first entry is shown in the display.  If the phonebook is empty, 

 will be displayed.

Press the         button.  Select NEW ENTRY if necessary and press the          button.  
Enter the name and press the         button.  Enter special characters and spaces by 
pressing the “1” button.  Enter the telephone number.  Press the          button to delete the 
last character or press and HOLD the         button to delete the whole entry.  You can enter 
a dialling pause (approximately 3 seconds) by pressing the          button. 

Press the         button.  Select HANDSET using             and press the         button.
Select AREA CODE using             and press the         button.  Enter the area code using 
key pad and confirm with the         button.