Digi Tech DigiTech Telephone C0408 Manuel D’Utilisation

When a station is busy on a call and another call
comes to the same station, the ringing of the second
call will automatically be subdued to a lower volume.

The system can be arranged to report alarm and status
conditions to a particular station or stations that have

been enabled to receive them. The station must be an
LCD speakerphone for this feature to be used. When
enabled to receive alarms, the station user can take
appropriate action to cause the alarm codes to be
presented on the LCD display. System and station

class of service programming are used to enable this
feature.

Ninety-nine system-wide speed dial numbers are
provided. 

 system speed dial numbers can be up

to thirty-two digits in length, and can include numbers,

 ‘s, S’s, pauses, and flash signals. System speed dial

numbers are programmed at station 10 or 12 for use at

every station in the system. No class of service is
required.

When the tandem attendant feature is enabled, a recall

from an unanswered call transfer or a timed hold recall
will ring at the normal attendant station (station 10) that

set the transfer or hold condition, and also at the

tandem attendant station (station 12). System class of

service programming is used to enable the tandem

attendant mode.

When host system custom calling features are
available via a hookflash signal, the system can be
programmed so that the TAP (RECALL) button will
generate a “flash” signal when it is pressed. When
custom calling features are not available, the TAP
(RECALL) button functions as a positive disconnect, or
dial tone, recall button. These two features are
mutually exclusive. The 

 time is

assigned through system class of service
programming.

One telephone system can be used for multiple

tenants at a location by having flexible line appearance

at each station. Button mapping for line appearance
can be performed on each station using the station
class of 

 programming. Refer to the discussion

titled: Square/Non-Square Configuration.

Description Of System 

After a call has been on hold for a programmed length
of time the system will recall the station that placed
the call on hold. The system class of service
programming sets the timed hold recall time period.

See the discussion titled: 

System toll call restriction can be configured to
prohibit some or all stations from calling a wide range
of number combinations. The restricted numbers are
specified on up to 16 tables. The system assigns
several broad-range values to two of these tables, and
assigns the tables to all lines as a default condition.
The default tables need only to be enabled on a per
station basis to activate the default toll restriction.

In general, toll restriction works as follows:

The programmable tables of restricted numbers
contain up to four entries with each entry containing
up to 16 digits.

Each table of restricted numbers can be programmed

to be an “allow” table or a “deny” table with entries in

an “allow” table overriding entries in a “deny” table.
This arrangement allows exceptions to toll restriction
to be enabled. For example, the dialing of

 numbers can be allowed even though

the dialing of all 1-xxx-xxx-xxxx numbers is denied.

A “match anything” symbol (# ) can be stored to

represent any digit from 0 to 9. The programmed toll
restriction tables are individually assigned to each
appropriate station and line. When an outside call is

dialed, the system examines the dialed number and

makes a comparison between 

 and the toll restriction

tables. Any tables assigned to BOTH the station being

used and the selected line determine the restrictions to
be imposed.

Dialing a restricted number on a restricted line from a

restricted station will cause the line to be automatically

disconnected from the station.

Toll table class of service programming is used to
create the tables of restricted numbers.

Toll restriction tables that will only take effect when the

system is in the night transfer (of ringing) mode, can
be assigned to any or all stations in the system. These

toll tables replace any that may be assigned to the

station during normal, or day mode, operation. For
example: A station that has no other toll restriction
table assigned to it can be programmed to receive a
toll restriction table which will restrict everything but