Crossover DAWF0EM Manuel Du Propriétaire

4

Laundrylux

112999-1

ANTI-WRINKLE
This program selection helps keep permanent press items

wrinkle free when they are not removed from the dryer promptly

at the end of the drying and cooling cycles.  The Anti-Wrinkle

program settings are:
1. Guard Delay Time ..............1 to 9 minutes
2. Guard On Time ...................1 to 99-seconds
3. Active Guard Time..............1 to 99 minutes

FREE DRY MODE
In this program selection, the dryer can be started without the

insertion of coins by simply pressing any one of the three

temperature selections.  When set in the “Free Dry” Mode,

the Phase 5 coin microprocessor controller (computer) can

also be programmed to run with an Automatic Cycle (percent

of dryness) or with a Timed Cycle.  If the “Free Dry” program

is utilized, the computer ’s L.E.D. display will cycle back and

forth between “FILL” to “FrEE,” unless otherwise programmed.

L.E.D. FLASH DISPLAY
Programmable to allow the L.E.D. readout to display a choice

of “FILL” (no cycle in progress), “Amount To Start” (i.e., 25¢),

or, in the case of free dry, “FrEE.”  This program selection also

allows the L.E.D. display to flash back and forth every

2-seconds from “FILL” to “Amount To Start” or, in the case of

free dry, from “FILL” to “FrEE.”

AUDIBLE TONE
In this program selection, a tone (buzzer) will sound for each

coin inserted, program entry, or at the drying and cooling cycles

for a period of 5-seconds to indicate that the cycle is complete.

Additionally, when in the  Anti-Wrinkle program, the tone

(buzzer) will sound for 5-seconds at the end of the “Guard On

Time.”

TEMPERATURE DISPLAY
This program selection enables the temperature in the dryer

to be viewed (°F or °C) either while the dryer is off or running.

This service feature shows that the dryer is maint aining the

selected temperature.

DIAGNOSTICS
All major circuits, including door, microprocessor temperature

sensor, heat, and motor circuit s are monitored.   There are

also indicators installed on the outputs of each relay to easily

identify failures, and the door switch has an indicator installed

on the Phase 5 microprocessor controller (computer) to help

indicate failure.

AUTOMATIC DRY TIME
This program selection allows the dryer to run up to a specific

time.  During the “AUtO” mode or “FrEE” dry mode this program

is only designed to limit the dryer’s operation during the drying

cycle.

ROTATIONAL SAFE GUARD (Optional)
This program monitors the rotation of the tumbler.  If the tumbler

is not rot ating, the Phase 5 coin microprocessor controller

(computer) will disable all output s, an audible tone (buzzer)

will sound, and an error message will be displayed.  

This

program selection can be programmed to be in the inactive

mode.

BATTERY BACKUP (Optional)
This feature allows the Phase 5 coin microprocessor controller

(computer) to maintain its operating status should a momentary

power interruption occur while the dryer cycle is in progress.

L.E.D. Display and Codes _____________

Automatic Cycle (Slope Program Factor)

Accumulative Coin

Maximum Auto Dryness Time

Amount for Additional Time

Active Anti-Wrinkle Guard Time

Accumulative Time

Amount To Start

Automatic Mode (Patent No. 4,827,627)

Automatic Cycle (Heat Loss [of fset] Factor)

Bad Coin Lockout

Bad Coin Reset

Buzzer (Tone)

Degree in Celsius

Clear Left Coin Count

Coin Mode

Clear Right Coin Count

Drying and Cooling Cycles Complete

or

Dryer is in Anti-Wrinkle Cycle

Door Circuit is Open*

Dryer Sensor Circuit Failure*

Degree in Fahrenheit

No Cycle in Progress

Flash Display Active

Free Dry Mode

Anti-Wrinkle Delay Time

Anti-Wrinkle On Time

Anti-Wrinkle Program Active

High Cool Down

Overheating Condition*

Left Coin Count

Left Coin Denomination

Low Cool Down

No Buzzer (Tone)

No Flash Display

No Anti-Wrinkle

No Rotational Sensor Selected

Percent Dry

Program Location

Program Location Automation Review

Permanent Press Cool Down

Permanent Press

Amount to start has been Inserted

Make Temperature Selection

Right Coin Count

Right Coin Denomination

Rotational Sensor Circuit Failure*

Rotational Sensor Selected

Time For Amount to Start

Timed Mode

* Refer to Phase 5 Coin System Diagnostics on page 36 for detailed information.