Crossover DAWF0EM Manuel Du Propriétaire
112999-1
www.Laundrylux.com
5
Operating Instructions _______________
NOTE: Unless otherwise specified at the time of ordering,
the Phase 5 coin microprocessor controller (computer) has
been preprogrammed by the factory with the parameters
shown on page 36. Should program changes be found
necessary, please read this Phase 5 Coin User’s Manual
carefully to thoroughly familiarize yourself with the Phase 5
coin microprocessor controller (computer) programming
characteristics.
the Phase 5 coin microprocessor controller (computer) has
been preprogrammed by the factory with the parameters
shown on page 36. Should program changes be found
necessary, please read this Phase 5 Coin User’s Manual
carefully to thoroughly familiarize yourself with the Phase 5
coin microprocessor controller (computer) programming
characteristics.
Timed Mode ___________________________
When turning on power or when no cycle is in progress, the
L.E.D. display will read “FILL” and/or “Amount To Start” (“AtSt”).
Insert coin(s). Once the correct “Amount To Start” has been
Insert coin(s). Once the correct “Amount To Start” has been
inserted, the L.E.D. display will read “PUSH.”
Select temperature by pushing “HI TEMP,” “LO TEMP,” or
Select temperature by pushing “HI TEMP,” “LO TEMP,” or
“PERM PRESS.” The dryer will start and the L.E.D. display
will read the temperature cycle selected and the drying time.
The dryer will continue through the drying and cooling cycles,
The dryer will continue through the drying and cooling cycles,
showing time counting downward.
NOTE: If the door is opened during a cycle, both the heat
and motor will stop. However, the Phase 5 coin
microprocessor controller (computer) will continue to count
downwards in time. Continuation of the cycle will resume
only after the door has been closed and any one of the
three temperature selection buttons is again depressed.
and motor will stop. However, the Phase 5 coin
microprocessor controller (computer) will continue to count
downwards in time. Continuation of the cycle will resume
only after the door has been closed and any one of the
three temperature selection buttons is again depressed.
Upon completion of the drying and cooling cycles, the buzzer
(tone) will sound, and the L.E.D. display will read “donE” for
5-seconds, at which time the dryer will shut off.
NOTE: If the Anti-Wrinkle Program is active (“Grd”), the
L.E.D. display will remain reading “donE,” and the Phase 5
coin microprocessor (computer) will proceed through the
Anti-Wrinkle Program until the maximum “Guard On Time”
has expired or until the door is opened, whichever comes
first. The L.E.D. display will read “FILL” and/or “Amount To
Start” (“AtSt”).
L.E.D. display will remain reading “donE,” and the Phase 5
coin microprocessor (computer) will proceed through the
Anti-Wrinkle Program until the maximum “Guard On Time”
has expired or until the door is opened, whichever comes
first. The L.E.D. display will read “FILL” and/or “Amount To
Start” (“AtSt”).
If the Anti-Wrinkle Program is not active (“nGrd”) the L.E.D.
display will read “donE” until the main door is opened, at
which time the L.E.D. display will read “FILL” and/or
“Amount To Start.”
display will read “donE” until the main door is opened, at
which time the L.E.D. display will read “FILL” and/or
“Amount To Start.”
Automatic Mode
(Patent No. 4,827,627) ________________
When turning on power or when no cycle is in progress, the
L.E.D. display will read “Fill” and/or “Amount To Start” (“AtSt”).
Insert coin(s). Once correct “Amount to S tart” has been
Insert coin(s). Once correct “Amount to S tart” has been
inserted, the L.E.D. display will read “PUSH.”
Select temperature by pushing “HI TEMP,” “LO TEMP,” or
Select temperature by pushing “HI TEMP,” “LO TEMP,” or
“PERM PRESS.” The dryer will start, the L.E.D. display will
read the temperature cycle selected, and the drying time
portion of the L.E.D. display will display the time and count
down as time elapses.
NOTE: If the door is opened during a cycle, both the heat
and motor will stop. However, the Phase 5 coin
microprocessor controller (computer) will continue to count
downwards in time. Continuation of the cycle will resume
only after the door has been closed and any one of the
three temperature selection buttons is again depressed.
and motor will stop. However, the Phase 5 coin
microprocessor controller (computer) will continue to count
downwards in time. Continuation of the cycle will resume
only after the door has been closed and any one of the
three temperature selection buttons is again depressed.
Once the preprogrammed dryness level and cool down period
have been reached or maximum automatic time has expired,
whichever comes first, the buzzer (tone) will sound, and the
L.E.D. display will read “donE” for 5-seconds, at which time
the dryer will shut off.
NOTE: If the Anti-Wrinkle Program is active (“Grd”), the
L.E.D. display will remain reading “donE,” and the Phase 5
coin microprocessor controller (computer) will proceed
through the Anti-Wrinkle Program until the maximum
“Guard On Time” has expired or door is opened, whichever
comes first. The L.E.D. will read “FILL” and/or “Amount To
Start” (“AtSt”).
L.E.D. display will remain reading “donE,” and the Phase 5
coin microprocessor controller (computer) will proceed
through the Anti-Wrinkle Program until the maximum
“Guard On Time” has expired or door is opened, whichever
comes first. The L.E.D. will read “FILL” and/or “Amount To
Start” (“AtSt”).
If the Anti-Wrinkle Program is not active (“nGrd”), the
L.E.D. display will read “donE” until the main door is
opened, at which time the L.E.D. display will read “FILL”
and/or “Amount To Start.”
L.E.D. display will read “donE” until the main door is
opened, at which time the L.E.D. display will read “FILL”
and/or “Amount To Start.”
Free Dry Mode ________________________
When turning on power or when no cycle is in progress, the
L.E.D. display will read “FILL” and/or “FrEE.”
Select temperature. The dryer will st art, the L.E.D. display
Select temperature. The dryer will st art, the L.E.D. display
will read the temperature cycle selected and the drying time
portion of the L.E.D. display will read the temperature cycle
selected. The drying time portion of the L.E.D. drying will read
“00” and count upward as time elap ses, or the vended time
will count downward, depending on which p arameter is
programmed.
NOTE: If the door is opened during a cycle, both the heat
and motor will stop. However, the Phase 5 coin
microprocessor controller (computer) will continue to count
the time, either upward or downward, depending on which
parameter is programmed. Continuation of the cycle will
resume only after the door has been closed and any one of
three temperature selection buttons is again depressed.
and motor will stop. However, the Phase 5 coin
microprocessor controller (computer) will continue to count
the time, either upward or downward, depending on which
parameter is programmed. Continuation of the cycle will
resume only after the door has been closed and any one of
three temperature selection buttons is again depressed.
Once the preprogrammed percent dryness level and cool down
period has been reached or maximum automatic time has
expired, whichever comes first, the tone (buzzer) will sound,
and the L.E.D. display will read “donE” for 5-seconds, at which
time the dryer will shut off.
NOTE: If the Anti-Wrinkle Program is active (“Grd”), the
L.E.D. display will remain reading “donE,” and the Phase 5
coin microprocessor controller (computer) will proceed
through the Anti-Wrinkle Program until the maximum
“Guard On Time” has expired or door is opened, whichever
comes first. The L.E.D. display will read “FILL” and/or
“Amount To Start” (“AtSt”).
L.E.D. display will remain reading “donE,” and the Phase 5
coin microprocessor controller (computer) will proceed
through the Anti-Wrinkle Program until the maximum
“Guard On Time” has expired or door is opened, whichever
comes first. The L.E.D. display will read “FILL” and/or
“Amount To Start” (“AtSt”).
If the Anti-Wrinkle Program is not active (“nGrd”), the
L.E.D. display will read “donE” until the main door is
opened, at which time the L.E.D. display will read “FILL”
and/or “Amount To Start.”
L.E.D. display will read “donE” until the main door is
opened, at which time the L.E.D. display will read “FILL”
and/or “Amount To Start.”