ATTO Technology 1500D/E Manuel D’Utilisation
35
ATTO Technology Inc. iPBridge Installation and Operation Manual
2.2.7 Ethernet commands
These commands configure the management and data Ethernet ports including Telnet parameters.
DPMTU
Controls the MTU (Maximum Transmission Unit) used by
the data port: increasing the MTU may improve
throughput on the ipBridge data ports. The MTU for the
management port cannot be changed.
Controls the MTU (Maximum Transmission Unit) used by
the data port: increasing the MTU may improve
throughput on the ipBridge data ports. The MTU for the
management port cannot be changed.
Default: 1514
Set syntax: set DPMTU dp0 [1514 | 9014]
Requires a SaveConfiguration command
Get syntax: get dp0 DPMTU
Set syntax: set DPMTU dp0 [1514 | 9014]
Requires a SaveConfiguration command
Get syntax: get dp0 DPMTU
EthernetSpeed
Specifies the speed of the Ethernet ports. If auto is
enabled, the speed will be negotiated.10 and 100 speeds
are half duplex Ethernet speed settings in the host must be
the same as Ethernet speed settings in the iPBridge. The
iPBridge default Ethernet speed is auto: your host must
be set to auto. If you set Ethernet speed to 10, your host
must be set to Ethernet speed 10, half duplex. If you set
Ethernet speed to 100, your host must be set to Ethernet
speed 100, half duplex.
Specifies the speed of the Ethernet ports. If auto is
enabled, the speed will be negotiated.10 and 100 speeds
are half duplex Ethernet speed settings in the host must be
the same as Ethernet speed settings in the iPBridge. The
iPBridge default Ethernet speed is auto: your host must
be set to auto. If you set Ethernet speed to 10, your host
must be set to Ethernet speed 10, half duplex. If you set
Ethernet speed to 100, your host must be set to Ethernet
speed 100, half duplex.
Choices are
10 = 10 baseT
100 = 100 baseT
1000 =1000baseT
100 = 100 baseT
1000 =1000baseT
Default: auto
Set syntax: set EthernetSpeed dp0 [10 | 100 | 1000| Auto]
Requires a SaveConfiguration command
Get syntax: get EthernetSpeed dp0
Set syntax: set EthernetSpeed dp0 [10 | 100 | 1000| Auto]
Requires a SaveConfiguration command
Get syntax: get EthernetSpeed dp0
Exit
Exits the current Telnet CLI session; it has no effect if
used during a serial CLI session.
Exits the current Telnet CLI session; it has no effect if
used during a serial CLI session.
Immediate command: Exit
IPAddress
Controls the IP address of the iPBridge Ethernet data
ports. If IPDHCP is enabled, the
Controls the IP address of the iPBridge Ethernet data
ports. If IPDHCP is enabled, the
get
command reports
the current IP address assigned by the network DHCP
server, followed by the DHCP identifier.
server, followed by the DHCP identifier.
Default IP address: 10.0.0.1
Set syntax: set IPAddress dp0 xxx.xxx.xxx.xxx
Requires a SaveConfiguration command
Get syntax: get IPAddress dp0
IPDHCP
Selecting DHCP allows the iPBridge to request an IP
address from the network DHCP server. The network
must have at least one DHCP server
Selecting DHCP allows the iPBridge to request an IP
address from the network DHCP server. The network
must have at least one DHCP server
Default: enabled
Set syntax: set IPDHCP dp0 [enabled | disabled]
Requires a SaveConfiguration command
Get syntax: get IPDHCP dp0
Set syntax: set IPDHCP dp0 [enabled | disabled]
Requires a SaveConfiguration command
Get syntax: get IPDHCP dp0
IPGateway
Controls the current gateway. If IPDHCP is enabled (see
above),
Controls the current gateway. If IPDHCP is enabled (see
above),
get
command reports the current IP gateway
assigned by the network DHCP server
Default: 0.0.0.0
Set syntax: set IPGateway dp0 xxx.xxx.xxx.xxx
Requires a SaveConfiguration command
Get syntax: get dp0 IPGateway
Set syntax: set IPGateway dp0 xxx.xxx.xxx.xxx
Requires a SaveConfiguration command
Get syntax: get dp0 IPGateway
IPSubnetMask
Controls the current subnet mask. If IPDHCP is enabled
(see above),
Controls the current subnet mask. If IPDHCP is enabled
(see above),
get
command reports the current subnet
mask assigned by the DHCP server
Default: 255.255.0.0
Set syntax: set IPSubnetMask dp0 xxx.xxx.xxx.xxx
Requires a SaveConfiguration command
Get syntax: get dp0 IPSubnetMask
Set syntax: set IPSubnetMask dp0 xxx.xxx.xxx.xxx
Requires a SaveConfiguration command
Get syntax: get dp0 IPSubnetMask
Password
Specifies a password for all sessions: Telnet, FTP and
ExpressNAV web-based interface. You will be prompted
for the current password, to enter the new password, and
to confirm the new password. Passwords are case
sensitive, 0-32 characters with no spaces.An empty
password can be configured by entering the Password
confirmation prompts with no parameters. The command
Specifies a password for all sessions: Telnet, FTP and
ExpressNAV web-based interface. You will be prompted
for the current password, to enter the new password, and
to confirm the new password. Passwords are case
sensitive, 0-32 characters with no spaces.An empty
password can be configured by entering the Password
confirmation prompts with no parameters. The command
RestoreConfiguration default
sets the password to its
default value.
Default: Password
Set syntax: set Password
Requires a SaveConfiguration command
Set syntax: set Password
Requires a SaveConfiguration command