ATTO Technology 1500D/E Manuel D’Utilisation
37
ATTO Technology Inc. iPBridge Installation and Operation Manual
2.2.8 iSCSI commands
You may customize the iPBridge to your specifications using the CLI commands in this section.
iSCSIAlias
Provides a human-readable name assigned to the
iPBridge. Aliases may be 1 to 64 characters long and may
contain spaces if spaces are enclosed in quotation marks.
Entering the
Provides a human-readable name assigned to the
iPBridge. Aliases may be 1 to 64 characters long and may
contain spaces if spaces are enclosed in quotation marks.
Entering the
set iSCSIAlias
command with no alias
parameter causes the alias to be removed.
Default: ““
Set syntax: set iSCSIAlias [Alias]
Requires a SaveConfiguration command
Get syntax: get iSCSIAlias
Set syntax: set iSCSIAlias [Alias]
Requires a SaveConfiguration command
Get syntax: get iSCSIAlias
iSCSIChap
Enables/disables requiring CHAP (Challenge-
Handshake Authentication Protocol) to be used for the
iSCSI protocol. If
Enables/disables requiring CHAP (Challenge-
Handshake Authentication Protocol) to be used for the
iSCSI protocol. If
MultiTargetMode
has been enabled, a
valid target name must be provided. If
CHAP
is enabled,
the target requires the initiator to negotiate CHAP
authentication using the CHAP secrets. An initiator may
reject this negotiation.
authentication using the CHAP secrets. An initiator may
reject this negotiation.
Default:disabled
In single target mode, set syntax: set iSCSIChap
[enabled | disabled]
In single target mode, get syntax: get iSCSIChap
In multiple target mode:, set syntax: set iSCSIChap
[Target Name] [enabled | disabled]
In multiple target mode, get syntax: get iSCSIChap
[Target Name]
In single target mode, set syntax: set iSCSIChap
[enabled | disabled]
In single target mode, get syntax: get iSCSIChap
In multiple target mode:, set syntax: set iSCSIChap
[Target Name] [enabled | disabled]
In multiple target mode, get syntax: get iSCSIChap
[Target Name]
iSCSIChapSecret
Specifies the incoming and outgoing passwords for iSCSI
chap sessions.
Specifies the incoming and outgoing passwords for iSCSI
chap sessions.
RestoreConfiguration default
sets the
CHAP secret passwords pair to default values.
Secrets are case sensitive, 12 (16 for Microsoft iSCSI
initiator) to 32 characters, and cannot contain spaces.
initiator) to 32 characters, and cannot contain spaces.
In
and
out
secrets must be different.
When either secret is all 0’s, iSCSI CHAP authentication
is disabled. Additionally, an all ‘0’ secret can be
configured by entering the iSCSIChapSecret command
confirmation prompts with no parameters.
is disabled. Additionally, an all ‘0’ secret can be
configured by entering the iSCSIChapSecret command
confirmation prompts with no parameters.
An
in
CHAP secret is for authentication of the server to
the iPBridge. The iPBridge can store up to 32
in
secrets,
each with a unique
Account Name
(optionally the
Initiator Name) and secret pair. The
Account Name
can
be 1 to 223 characters.
Account Names
are case
sensitive. Account name can not be
all
.
An
out
chap secret is for authentication of the iPBridge to
the rest of the network. There can only be one out secret.
The account name is ignored for out secrets and defaulted
to
The account name is ignored for out secrets and defaulted
to
root
.
In single target mode, set syntax: set iSCSIChapSecret
[in | out | delete] [Account Name] <Secret>
In single target mode, get syntax: get iSCSIChapSecret
[Account Name | all]
In multiple target mode, set syntax: set iSCSIChapSecret
[Target Name] [in | out | delete] [Account Name] <Secret>
In multiple target mode, get syntax: get iSCSIChapSecret
[Target Name] [Account Name | all]
[in | out | delete] [Account Name] <Secret>
In single target mode, get syntax: get iSCSIChapSecret
[Account Name | all]
In multiple target mode, set syntax: set iSCSIChapSecret
[Target Name] [in | out | delete] [Account Name] <Secret>
In multiple target mode, get syntax: get iSCSIChapSecret
[Target Name] [Account Name | all]
iSCSIPortNumber
Specifies the port number whereby the iPBridge will
listen for iSCSI connections. The port number must be
between 1024 and 65535 except for port 860.
Specifies the port number whereby the iPBridge will
listen for iSCSI connections. The port number must be
between 1024 and 65535 except for port 860.
Default: 3260
Set syntax: set iSCSIPortNumber portnum
Requires a SaveConfiguration command
Get syntax: get iSCSIPortNumber
Set syntax: set iSCSIPortNumber portnum
Requires a SaveConfiguration command
Get syntax: get iSCSIPortNumber
iSCSITarget
Creates/deletes an iSCSI target name. The target name
will act as a suffix to the standard bridge iSCSI-qualified
name. The target name may not exceed 24 characters. A
newly-created target has one LUN, the iPBridge LUN, at
LUN 0. If the target name already exists, this command
does nothing.
Creates/deletes an iSCSI target name. The target name
will act as a suffix to the standard bridge iSCSI-qualified
name. The target name may not exceed 24 characters. A
newly-created target has one LUN, the iPBridge LUN, at
LUN 0. If the target name already exists, this command
does nothing.
MultiTargetMode
must be enabled to use
this command. In verbose mode, overwriting a map
requires secondary confirmation of the action.
requires secondary confirmation of the action.
Immediate command: iSCSI [Target Name] <delete>
iSNSLoginControl
Specifies whether the iPBridge will delegate its access
control/authorization to an iSNS server.
Specifies whether the iPBridge will delegate its access
control/authorization to an iSNS server.
Default: disabled
Set syntax: set iSNSLoginControl [enabled | disabled]
Requires a SaveConfiguration command
Get syntax: get iSNSLoginControl
Set syntax: set iSNSLoginControl [enabled | disabled]
Requires a SaveConfiguration command
Get syntax: get iSNSLoginControl