ATTO Technology 1500D/E Manuel D’Utilisation
41
ATTO Technology Inc. iPBridge Installation and Operation Manual
2.2.10 Privileged OEM configuration services
Privileged OEM configuration services perform OEM-specific product branding and labeling functions
only available to OEM customers such as vendor, product, and model number identification during
power up display.
only available to OEM customers such as vendor, product, and model number identification during
power up display.
Privileged OEM Configuration commands may
only be “set” from within an OEM config file.
only be “set” from within an OEM config file.
The OEM config file is an ASCII text file which
contains all the CLI commands that can be used to
override the factory default settings of the
iPBridge. It consists of a header record and a list
of CLI commands. Each line may contain up to
128 characters and must be terminated by any of
the standard EOL combinations such as
contains all the CLI commands that can be used to
override the factory default settings of the
iPBridge. It consists of a header record and a list
of CLI commands. Each line may contain up to
128 characters and must be terminated by any of
the standard EOL combinations such as
\r, \n,
or
\r\n
. Updates may be loaded via any of the current
firmware update methods (see
The commands do not result in reservation of the
iPBridge. The information in a “get” command
may only be displayed within a TTY CLI session.
These commands will not be displayed in the help
menu.
iPBridge. The information in a “get” command
may only be displayed within a TTY CLI session.
These commands will not be displayed in the help
menu.
To configure iPBridge product identifiers
1
Create an OEM configuration file containing
valid and applicable CLI commands.
valid and applicable CLI commands.
2
Upload the OEM configuration file to the
iPBridge via any of the currently available
methods (see
iPBridge via any of the currently available
methods (see
3
Initiate the OEM configuration file by typing
RestoreConfiguration default
and pressing enter
at the CLI prompt, or by applying an NVRAM
default jumper to the circuit board.
default jumper to the circuit board.
4
Power cycle.
Note
To restore factory default settings, type
RestoreConfiguration ATTO, press Enter at
the CLI prompt, and cycle power.
RestoreConfiguration ATTO, press Enter at
the CLI prompt, and cycle power.
AutoMapOnBoot
Enables or disables an automatic bus scan and device
mapping operation at boot time.
Enables or disables an automatic bus scan and device
mapping operation at boot time.
Default: enabled
Set syntax: set AutoMapOnBoot [enabled |disabled]
Get syntax: get AutoMapOnBoot
Set syntax: set AutoMapOnBoot [enabled |disabled]
Get syntax: get AutoMapOnBoot
ColdReset
When enabled, the iPBridge will reboot when a Cold
Reset command is received. When disabled, the iPBridge
will not reboot, but will respond to the host with
When enabled, the iPBridge will reboot when a Cold
Reset command is received. When disabled, the iPBridge
will not reboot, but will respond to the host with
status
unsupported.
Default:enabled
Set syntax:set ColdReset [enabled | disabled]
Get syntax: ColdReset
Set syntax:set ColdReset [enabled | disabled]
Get syntax: ColdReset
InquiryProductID
Controls the product ID string displayed by the iPBridge
in response to a SCSI INQUIRY command. The ID is
padded with 0s to a maximum 16 characters
Controls the product ID string displayed by the iPBridge
in response to a SCSI INQUIRY command. The ID is
padded with 0s to a maximum 16 characters
Default: iPBridge 1500 or iPBridge 1550
Set syntax: set InquiryProductID [string]
Requires a SaveConfiguration command
Get syntax: get InquiryProductID
Set syntax: set InquiryProductID [string]
Requires a SaveConfiguration command
Get syntax: get InquiryProductID
InquiryVendorID
Controls the vender ID string displayed by the iPBridge
in response to a SCSI INQUIRY command. The ID is
padded with 0s to a maximum 8 characters
Controls the vender ID string displayed by the iPBridge
in response to a SCSI INQUIRY command. The ID is
padded with 0s to a maximum 8 characters
Default: ATTO
Set syntax: set InquiryVendorID [string]
Requires a SaveConfiguration command
Get syntax: get InquiryVendorID
Set syntax: set InquiryVendorID [string]
Requires a SaveConfiguration command
Get syntax: get InquiryVendorID
IqnVendorPrefixID
Displays the vendor prefix ID of the iSCSI qualified name
(iqn). The vendor prefix includes iqn ID string, date code,
and naming authority.
Displays the vendor prefix ID of the iSCSI qualified name
(iqn). The vendor prefix includes iqn ID string, date code,
and naming authority.
Set syntax:set IqnVendorPrefixID [string]
Get syntax: get IqnVendorPrefixID
Get syntax: get IqnVendorPrefixID