ATTO Technology 1500D/E Manuel D’Utilisation
39
ATTO Technology Inc. iPBridge Installation and Operation Manual
2.2.9 Mapping commands
You may map devices via the web-based server or through the management or serial ports.
AutoMap
Automatically assigns a subset of iSCSI LUNs to a subset
of SCSI target destination devices visible to the
iPBridge.Valid existing maps will not be deleted.
Automatically assigns a subset of iSCSI LUNs to a subset
of SCSI target destination devices visible to the
iPBridge.Valid existing maps will not be deleted.
Immediate command: AutoMap
iSCSITarget
Creates/deletes an iSCSI target name. The target name
will act as a suffix to the standard bridge iSCSI-qualified
name. The target name may not exceed 24 characters. A
newly-created target has one LUN, the iPBridge LUN, at
LUN 0. If the target name already exists, this command
does nothing.
Creates/deletes an iSCSI target name. The target name
will act as a suffix to the standard bridge iSCSI-qualified
name. The target name may not exceed 24 characters. A
newly-created target has one LUN, the iPBridge LUN, at
LUN 0. If the target name already exists, this command
does nothing.
MultiTargetMode
must be enabled to use
this command. In verbose mode, overwriting a map
requires secondary confirmation of the action.
requires secondary confirmation of the action.
Immediate command: iSCSITarget [Target Name]
<delete>
<delete>
MultiTargetMode
Enables/disables iSCSI multiple target mode addressing
on the iPBridge. If enabled, all previous maps will be
deleted. In verbose mode, overwriting a map requires
secondary confirmation of the action.
Enables/disables iSCSI multiple target mode addressing
on the iPBridge. If enabled, all previous maps will be
deleted. In verbose mode, overwriting a map requires
secondary confirmation of the action.
Default: disabled
Set syntax: set MultiTargetMode [enabled | disabled]
Get syntax: get MultiTargetMode
Set syntax: set MultiTargetMode [enabled | disabled]
Get syntax: get MultiTargetMode
Route
Assigns a host protocol address to a target destination
device.If
Assigns a host protocol address to a target destination
device.If
MultiTargetMode
has been enabled, a valid
target name must be specified. If you try to map a new
SCSI BTL to the same iSCSI LUN, the new BTL
overwrites the previous map. Using the Delete identifier
removes the map from its map table. In verbose mode,
SCSI BTL to the same iSCSI LUN, the new BTL
overwrites the previous map. Using the Delete identifier
removes the map from its map table. In verbose mode,
overwriting a map requires secondary confirmation of the
action.
action.
Immediate command in single target mode:
Route iSCSI [lun] [SCSI [bb tt ll] | Delete]
Immediate command in multiple target mode:
Route iSCSI [Target Name] [lun] [SCSI [bb tt ll] | Delete]
Route iSCSI [lun] [SCSI [bb tt ll] | Delete]
Immediate command in multiple target mode:
Route iSCSI [Target Name] [lun] [SCSI [bb tt ll] | Delete]
RouteDisplay
Displays a list of iSCSI to SCSI Bus, Target, LUN
mappings. If MultiTargetMode has been enabled, the
optional
Displays a list of iSCSI to SCSI Bus, Target, LUN
mappings. If MultiTargetMode has been enabled, the
optional
Target Name
parameter limits the list to the
maps which satisfy a search for the given target name. In
either mode, the optional
either mode, the optional
LUN
parameter will limit the
list to the map which satisfies a search for the given
LUN
.
NumEntries: decimal number of map lines displayed
Target Name: target name
Lun : target LUN
sb: decimal SCSI bus number
st: decimal SCSI target number
sl: decimal SCSI LUN number
Target Name: target name
Lun : target LUN
sb: decimal SCSI bus number
st: decimal SCSI target number
sl: decimal SCSI LUN number
Immediate command, single target mode:
RouteDisplay iSCSI <lun>
Immediate command, multiple target mode:
RouteDisplay iSCSI <Target Name> <lun>
RouteDisplay iSCSI <lun>
Immediate command, multiple target mode:
RouteDisplay iSCSI <Target Name> <lun>
SCSIInitID
Specifies the SCSI initiator ID to be used on the specified
SCSI port. All maps coinciding with the user-specified
SCSIInitID must be set to offline and will become invalid
upon issuing this command. Choices are 0 to 15.
Specifies the SCSI initiator ID to be used on the specified
SCSI port. All maps coinciding with the user-specified
SCSIInitID must be set to offline and will become invalid
upon issuing this command. Choices are 0 to 15.
Default: 7
Set syntax: set SCSIInitID [sb [0-15] ]
Requires a SaveConfiguration command
Get syntax: get SCSIInitID
Set syntax: set SCSIInitID [sb [0-15] ]
Requires a SaveConfiguration command
Get syntax: get SCSIInitID
SCSITargets
Returns a list of SCSI devices operational on the SCSI
port.
Returns a list of SCSI devices operational on the SCSI
port.
Immediate command: SCSITargets 0