Hubbell MSH Manuel D’Utilisation

3

 All welded carbon steel vessel designed and built in

strict accordance with the ASME Code Section IV and

stamped, certified, and registered with the National Board

of Boiler and Pressure Vessel Inspectors.

 All internal tank surfaces are lined with a minimum of 5/8"

thick Hydrastone cement for superior protection and tank

longevity.

 Designed for 100psi working pressure and hydrostatically

tested at 150psi (1 1/2 times the WP).

 Heavy duty 2" thick fiberglass blanket insulation covers

the pressure vessel for maximum operating efficiency and

minimal standby heat loss.

 Heavy gauge galvanized steel protective jacket holds

insulation in place and protected to ensure highly efficient

operation.

 Integrally welded bulkhead attachment points.

 Entire vessel is supported on heavy duty integrally welded

steel supports for sturdy deck mounting.

 Full five (5) year Non Pro-Rated tank warranty and one (1)

year electrical component warranty.

 Bronze ASME/CSA rated combination temperature and

pressure safety relief valve set at the vessel working

pressure and 210ºF.

 ABS approved and in conformance with USCG

regulations.

 All electrical operating controls are factory sized,

selected, wired, tested, and mounted in a NEMA 1

enclosure to ensure safe and reliable operation.

 A power distribution block is supplied for single point

electrical installation.

 Power fuses rated at a maximum of 60 Amps protect

each heating element branch circuit per NEC and UL

requirements. Each branch circuit has a maximum rating

of 48 Amps.

 Heavy duty definite purpose magnetic contactor with

integrally mounted power fuse block assembly switches

power on/off to each branch circuit.

 Heavy duty removable flange type immersion heating

element provides long service life.

 Fully adjustable thermostat maintains accurate water

temperature and is sized by the factory to control the

appropriate number of heating element circuits.

 A generously sized transformer provides fused 120V to

the control circuit

 A fully adjustable (100-240 ºF) safety hi-limit device with

manual reset interrupts power to the control circuit in the

event of over-temperature water in the storage tank.

 Safety door interlock mechanism interrupts power to the

control circuit upon opening the electrical control panel.

 Louvers in the control panel allow for cooling of the

electrical components to ensure maximum electrical

component longevity (when required).

  

 Phenolic epoxy resin.

  

 Stainless Steel (Please specify Type: 304, 316 or 316L)

 90/10 Copper-Nickel, other.

  

 Please specify

  

Skid mounting on heavy duty all welded I Beam

  

Type 304 stainless steel protective jacket,

please specify if painted.

   3

Dual energy package provides operational flexibility

for electric and (steam or boiler

water) power.

 See page 8 for details.

  

.  NEMA 4 watertight enclosure for outdoor/wet locations.

  

.  Explosion resistant enclosure for hazardous locations.

Please specify class, division, and group.

  

.  Built-in circuit breaker (with or without shunt trip) or a

built-in non-fused On/Off disconnect switch.

  

.  Alternate element sheath material (Please specify:

Incoloy, Stainless Steel, other).

  

.  Specialized heating element construction including:

Special watt density rating, passivation, electropolishing,

hermetic seals or any other feature required to meet the

needs of your application.

  

.  Factory installed low water cut out device to disengage

electrically the heating element(s) in the event of

insufficient water in the tank.

  

.  Dial thermometer and pressure gauge factory installed in

the tank.

  

.  Intra-tank circulation pump package with On/Off switch to

continuously circulate water within the tank and thereby

reduce stratification. All bronze circulator pump is rated

1/12 HP, 120V, 1 Ph.

  

.  Status indicating lamp(s).

  

.  Audible alarm system.

  

.  Digital display electronic temperature controller. Please

specify with or without RS485 communication port for

remote operation of the temperature controller.

  

.  Additional ground connections