Sunrise Medical Z-Bop Manuel D’Utilisation
932213 Rev. C
28
E N G L I S H
X I .
J. TOOLS YOU WILL NEED
1. Basic Tool Kit:
To set-up, adjust and maintain your chair you will need the follow-
ing tools:
ing tools:
•3mm Allen Wrench
•5mm Allen Wrench
•6mm Allen Wrench
•8mm Allen Wrench
•13mm Open-end Wrench
•17mm Socket Wrench
•13mm Socket Wrench
•16mm Open-end Wrench
•19mm Open-end Wrench
•Flat Head Screwdriver
•Phillips screwdriver #2
•Standard Tools
•7/16" box & open-end wrench
•1/2" box and open-end wrench
•3/4" box and open-end wrench
•5/32" Allen wrench
•Custom axle wrench
•Tire Pressure Gauge
•5mm Allen Wrench
•6mm Allen Wrench
•8mm Allen Wrench
•13mm Open-end Wrench
•17mm Socket Wrench
•13mm Socket Wrench
•16mm Open-end Wrench
•19mm Open-end Wrench
•Flat Head Screwdriver
•Phillips screwdriver #2
•Standard Tools
•7/16" box & open-end wrench
•1/2" box and open-end wrench
•3/4" box and open-end wrench
•5/32" Allen wrench
•Custom axle wrench
•Tire Pressure Gauge
You can obtain a multi-purpose tool kit from Sunrise, or buy the tools you need
from a hardware store.
2. Torque Wrench:
If you plan to adjust and maintain this chair yourself, Sunrise recom-
mends that you use a torque wrench.
If you plan to adjust and maintain this chair yourself, Sunrise recom-
mends that you use a torque wrench.
Q-NOTE– The wrench must measure inch-pounds. You can buy a
torque wrench and proper sockets from a hardware store.
applicable on solid aluminum rim), and remove tire and solid
insert.
insert.
h. Repair or replace inner tube (replace rim strip if necessary).
Q-NOTE– Do not use pneumatic inner tube in tires with two-piece
rims.
i.
Reassemble the wheel.Use a torque setting of 420 in.-lbs. to
re-tighten bolts.
re-tighten bolts.
j.
Install wheel on chair by replacing center lock washer, nut
and plastic dome. Use a torque setting of 180 in.-lbs. to
retighten bolts.
and plastic dome. Use a torque setting of 180 in.-lbs. to
retighten bolts.
k. Inflate tire to proper pressure level (listed on tire sidewall).
G. MOTOR BRUSHES
Check the motor brushes every four (4) months for wear. The
brushes should be clean and shiny. Replace worn or blackened
brushes.
brushes should be clean and shiny. Replace worn or blackened
brushes.
H. ORDERING PARTS
When you order parts, provide the following:
1. Model of chair
2. Serial number of chair
3. Left hand or right hand control
4. Part number, description and quantity of parts you need.
5. State reason for replacement.
2. Serial number of chair
3. Left hand or right hand control
4. Part number, description and quantity of parts you need.
5. State reason for replacement.
I. MAINTENANCE CHART
You should check the items on this chart at the indicated intervals.
If any of the items are loose, worn, bent or distorted, immediately
have them checked and/or repaired by your authorized Sunrise
supplier. Frequent maintenance and servicing will improve perform-
ance and extend wheelchair life, and help prevent injuries.
If any of the items are loose, worn, bent or distorted, immediately
have them checked and/or repaired by your authorized Sunrise
supplier. Frequent maintenance and servicing will improve perform-
ance and extend wheelchair life, and help prevent injuries.
Charge batteries
3
Check tires for proper inflation level
3
Check batteries for proper electrolyte level (wet cell only)
3
Check plugs and connectors for proper connections
3
Check all moving parts for wear
3
Inspect all nuts, bolts and fasteners for looseness or wear
3
Inspect upholstery for wear
3
Remove and inspect motor brushes
3
Service by authorized supplier
3
Daily
W
eekly
M
on
thly
Qu
arterly
Ann
u
ally
CHECK...