Sunrise Medical Quickie P120 Manuel D’Utilisation
26
27
930373 Rev. B
930373 Rev. B
I X .
S E T U P ,
A D J U S T M E N T & U S E
D.TO FIND & CORRECT
A PROBLEM
1 First: Follow steps in this section to make
sure set-up is correct.
2. Second: If step 1 does not work, consult
your supplier for help.
3. If You Still Have A Problem: contact
Sunrise Medical Customer Service at
(800) 456-8165.
(800) 456-8165.
E. BATTERIES (See Section XI)
F. FOOTRESTS
1.To Install:
a. Place swing-away pivot saddle (1) into the
receiver (2) on the front frame tube.
Footrest should face outward from frame.
Footrest should face outward from frame.
b. Rotate footrest inward until latch plate
(3) locks into place on locking bolt (4).
2.To Remove:
a. Press quick-release lever (5).
b. Rotate footrest outward and lift.
3.To Adjust Height:
a. Loosen the retaining bolt (6) in
the hanger frame clamp.
b. Reposition footrest height.
c. Re-tighten bolt.
G.ELEVATING LEGREST (OPTIONAL)
1.To Install Or Remove:
Follow same steps as for standard footrests.
2.To Adjust:
a.To raise legrest, lift to desired position.
Legrest will lock in place.
b.To lower legrest, first lift slightly then,
press release lever (7) down and lower
legrest to desired position. Legrest will
lock in place.
legrest to desired position. Legrest will
lock in place.
H.INTEGRAL JOYSTICK
1.To Connect:
1.To Connect:
a. Line up receptacle on large rectangular
connector (Beau Connector) (8), with
the pins on the Joystick box (9).
the pins on the Joystick box (9).
b. Push in firmly.
2.To Disconnect:
Pull back on connector until it disconnects
from Joystick box.
from Joystick box.
3
6
7
8
9
5 4
2
1
I X .
S E T - U P ,
A D J U S T M E N T & U S E
B. TOOLS YOU WILL NEED
1. Basic Tool Kit:
1. Basic Tool Kit:
To set-up, adjust and maintain your chair you will need the following tools:
•
•
7/16" box and open-end wrench
•
1/2" box and open-end wrench
•
3/4" box and open-end wrench
•
5/32" Allen wrench
•
3/16" Allen wrench
•
Phillips screwdriver #2
• Custom axle wrench (or a 1/2" open-end wrench)
You can obtain a multi-purpose tool kit from Sunrise, or buy the tools you
need from a hardware store.
You can obtain a multi-purpose tool kit from Sunrise, or buy the tools you
need from a hardware store.
2. Torque Wrench:
If you plan to adjust and maintain this chair yourself, Sunrise recommends that you
use a torque wrench.
use a torque wrench.
Note: The wrench must measure inch-pounds.You can buy a torque wrench and proper
sockets from a hardware store.
C. CHECK-OUT
Be sure this chair performs to your chosen operational settings. If it does not,
turn the chair off immediately and reprogram with the Quickie Integral
Programmer (QIP). If you do not own a Quickie Integral Programmer have
your supplier reprogram your wheelchair as needed. Or, you can order a
Quickie Integral Programmer for your own use, from your supplier.
turn the chair off immediately and reprogram with the Quickie Integral
Programmer (QIP). If you do not own a Quickie Integral Programmer have
your supplier reprogram your wheelchair as needed. Or, you can order a
Quickie Integral Programmer for your own use, from your supplier.
Note: Repeat this procedure until the chair performs to your specifications.
Note: Quickie’ Smart Pad Programmer or Smart Box Programmer are not compatible
with the P120 controller.
When properly set-up, this chair will operate smoothly. Check to see that all components
work properly. If you detect a problem, be sure to correct it before use.