Funai 31B-254 Manuale Utente

6

EN

Video channel setting will be necessary, if your VCR is 
connected to the TV via the RF cable.

• Use the remote control for this procedure.
1) Insert a pre-recorded tape into the VCR.

The VCR will turn on and start playback automatically.
If playback does not start, press 

K

.

2) Select and adjust your TV to channel 35. 

•If the playback picture appears on the TV screen, 

continue with step 

.

•If channel 35 is set for broadcasting, or interference lines 

appear on the picture, the RF converter must be set to a 
different channel between CH22 and CH69. Continue 
with step 

.

3) Press 

.

4) Press 

K

 or 

L

 repeatedly to select to 

“INITIAL”. Then, press 

B

.

5) Press 

K

 or 

L

 repeatedly to select to “RF 

OUT”. Then, press 

B

. The RF OUT CH menu 

will appear.

6) Press 

K

 or 

L

 to select a channel which is not 

used for broadcasted between channel 22 and channel 69 
in your area, then press 

B

. 

7) Press 

 to exit.

Set the TV channel to the RF OUT CHANNEL which 
was selected on the VCR.  A picture from the VCR will 
appear on the TV screen. If a picture does not appear, 
repeat steps 

 to 

 using a different channel which is not 

used for broadcast.

8) Press 

L

 to stop the tape.

You may also access the RF OUT CH menu by pressing 
and holding 

 on the remote control for 3 seconds 

during power off until the RF OUT CH menu appears.

This VCR incorporates a 24-hour clock. The clock must be set 
for the Timer Recording function to operate correctly.

• Use the remote control for this procedure.
1) Press 

.

2) Press 

K

 or 

L

 to select “INITIAL”, then press 

B

.

3) Press 

K

 or 

L

 to select “CLOCK”, then press 

B

.

4) (31B-254 and 31B-454 only)

Press 

K

 or 

L

 to select “MANUAL” or 

“AUTO”, then press 

B

.

•If you select “MANUAL”, continue with step 

.

•If you select “AUTO”, Auto Clock Setting becomes 

“ON”. Press 

. The clock will appear on the 

TV screen when you turn on the VCR again.

5) Press 

K

 or 

L

 until the relevant year appears, 

then press 

B

. 

6) Press 

K

 or 

L

 until the relevant month 

appears, then press 

B

.

7) Press 

K

 or 

L

 until the relevant day appears, 

then press 

B

. 

8) Press 

K

 or 

L

 until the relevant hour appears, 

then press 

/

B

.

9) Press 

K

 or 

L

 until the relevant minute 

appears.

10)Press 

 to start the clock. 

• Press 

s

 to go one step back from the current step 

during steps 

 to 

.

• Although seconds are not displayed, they begin counting 

from 00 when you exit by pressing 

. Use this feature 

to synchronize the clock with the correct time.

• If the VCR is unplugged or if there is a power failure for 

more than 30 seconds, you may have to reset the clock.

[AUTO CLOCK] (31B-254 and 31B-454 only)
• Channel Presetting must be set before the Auto Clock is 

set. 

• To set the clock automatically, the channel assigned to 

position 01 must have the PDC signal.

• The clock cannot be set automatically if you are not 

receiving a channel that carries a time signal in your area. In 
this case, set the clock manually.

• Once the auto clock setting is performed, the VCR will 

correct the current time by receiving PDC broadcasts 
whenever you turn off the VCR.

• The VCR will correct the current time automatically at 

8:00, if the VCR power is turned off.

• Between 23:00~1:00, the AUTO CLOCK function does 

not work even if the VCR power is turned off.

MENU

TIMER
SET UP
INITIAL

RF  OUT  CH  35

INITIAL

CH TUNING
CLOCK
RF OUT

MENU

TIMER
SET UP
INITIAL

INITIAL

CH TUNING
CLOCK
RF OUT

CLOCK

YEAR

2 0 0 6

MONTH

0 1

DAY

0 4  WE

HOUR

_ _

MINUTE

_ _

HM210BD(EN).fm  Page 6  Thursday, March 2, 2006  6:07 PM