Funai 31B-254 Manuale Utente

7

EN

Tuning of broadcast channels not already preset in the VCR 
can be performed in two ways.

• By “AUTOMATICALLY” tuning channels and placing 

them in sequential order in the VCR’s memory i.e. the first 
channel found will be memorized into the VCR’s channel 
position 1, the second channel found will be memorized 
into the VCR’s channel position 2 and so on.

• Execution of the “Automatic” channel presetting cancels all 

the preset channels. DO NOT use this feature if you intend 
to use some of the pre-tuned channels. Use the “Manual” 
channel presetting function to tune in the additional 
channels you require.

• Each channel is tuned manually and individually. Follow 

the steps laid out in the “Manual Channel Preset” section.

• It is necessary to set the video channel if your VCR is 

connected to the TV via the RF cable, and TV channel 35 
is set for broadcasting, or interference lines appear on the 
picture. Please refer to “Video Channel Setting”.

You can programme the tuner to scan only the channels that 
you can receive in your area.

• Use the remote control for this procedure.
1) Turn on the TV and select the TV channel to the video 

channel on the TV.

2) Press 

.

3) Press 

K

 or 

L

 to select “INITIAL”, then press 

B

.

4) Press 

K

 or 

L

 to select “CH TUNING”, then 

press 

B

.

5) Press 

K

 or 

L

 to select “AUTO”, then press 

B

.

• The tuner scans and memorizes all the active channels in 

your area. After scanning, the tuner stops on the lowest 
memorized channel.

You can select a desired channel by using 

 (

K

L

), or 

directly pressing the 

 on the remote control.

• Enter a channel number as a two-digit number for the 

quickest results. For example, to select channel 6, press 

 

and 

. If you only press 

, channel 6 will be selected after a 

brief delay.

• You can only select channels 1–99.

• Use the remote control for this procedure.
1) Press 

.

2) Press 

K

 or 

L

 to select “INITIAL”, then press 

B

.

3) Press 

K

 or 

L

 to select “CH TUNING”, then 

press 

B

.

4) Press 

K

 or 

L

 to select “MANUAL”, then 

press 

B

.

5) Press 

K

 or 

L

 to select “POSITION”, then 

press 

B

.

•When a weak signal is received in Manual Tuning mode, 

you can change the background to solid blue or the 
static screen by pressing 

.

6) Press the 

, 

K

, or 

L

 to select 

your desired position number, then press 

B

.

•You can select position number 01-99.
•If [ON] appears on the right side of “SKIP”, press 

K

 or 

L

 to point to “SKIP”. Then, press 

B

 to select [OFF].

•If you want to remove scrambled signals, press 

K

 

or 

L

 repeatedly to point to “DECODER”. Then, 

press 

B

 to select [ON].

7) Press 

K

 or 

L

 to select “CHANNEL”, then 

press 

B

.

Press 

K

 or 

L

. The VCR tuner will begin to 

search up or down automatically. When a channel is 
found, the VCR will stop searching and the picture will 
appear on the TV Screen.

•You can select desired channel number by using the 

. You must refer to the following 

Channel Plan table and press three digits to select the 
channel number. 
(To select channel 24, press “

” button first and then 

press “

” and “

”.)

•If this is the channel you want, press 

B

.

This VCR can receive Hyper and Oscar frequency bands.

8) Press 

 to exit.

To confirm that a channel has been added, press 

 (

K

L

).

INITIAL

CH TUNING
CLOCK
RF OUT

CH TUNING

AUTO
MANUAL
MOVE

scanning

MENU

TIMER
SET UP
INITIAL

01 – 10

IRA – IRJ, GAP

21 – 69

E21 – E69

74 – 78

X, Y, Z, Z+1, Z+2

80 – 99, 100

S1 – S20, GAP

121 – 141

S21 – S41

INITIAL

CH TUNING
CLOCK
RF OUT

CH TUNING

AUTO
MANUAL
MOVE

MANUAL

POSITION
CHANNEL
DECODER
SKIP

P08

008

[OFF]
[OFF]

MENU

TIMER
SET UP
INITIAL

HM210BD(EN).fm  Page 7  Thursday, March 2, 2006  6:07 PM