Blomberg TAF 7239 Manuale Utente

3 - EN

This section includes safety information that will 

help protection from risks of personal injuries 

or materialistic damages. Failure to follow 

these instructions shall cause any warranty and 

reliability commitment to become void.

•  Never place the machine on a carpet-

covered floor, otherwise, lack of airflow 

beneath the machine may cause electrical 

parts to overheat. This will cause problems 

with your machine.

•  If the power cable or mains plug is 

damaged, you must call Authorised Service 

Agent for repair.

•  The product should not be plugged in 

during installation, maintenance and repair 

works. Such works should always be made 

by the technical service. Manufacturer 

shall not be held responsible for damages 

arising from processes carried out by 

unauthorised persons.

•  Connect the product to a grounded outlet 

protected by a fuse of suitable capacity as 

stated in the technical specifications table.

•  Operate your product at temperatures 

between +5°C and +35°C.

•  Do not use electrical devices in the 

product.

•  Do not connect the air exit of the product 

to the chimney holes which are used for 

the exhaust fumes of the devices operating 

with gas or other types of fuel.

•  You must provide enough ventilation in 

order to prevent gases exiting from devices 

operating with other types of fuels including 

the naked flame from accumulating in the 

room due to the back fire effect.

•  Always clean the lint filter before or after 

each loading.

•  Never operate your dryer without the lint 

filter installed.

•  Do not allow fibre, dust and dirt 

accumulation around the exhaust exit and 

at adjacent areas.

•  Power cable plug must be within easy 

reach after installation.

•  Do not use extension cords, multi-plugs 

or adaptors to connect the dryer to power 

supply in order to decrease the risk of 

electric shock.

•  Do not make any changes on the plug 

supplied with the product. If it is not 

compatible with the socket, have a 

qualified electrician change the socket with 

a suitable one.

•  Items cleaned or washed with gasoil/

fuel oil, dry-laundry solvents and other 

combustible or explosive materials as 

well as the items that are contaminated 

or spotted with such materials should not 

be dried in the product since they emit 

flammable or explosive vapor.

•  Do not dry items cleaned with industrial 

chemicals in the dryer.

•  Do not dry unwashed items in the dryer.

•  Items soiled with cooking oils, acetone, 

alcohol, fuel oil, kerosene, stain remover, 

turpentine, paraffin and paraffin removers 

must be washed in hot water with plenty of 

detergent before being dried in the dryer.

•  Garments or pillows bolstered with rubber 

foam (latex foam), shower bonnets, water 

resistant textiles, materials with rubber 

reinforcement and rubber foam pads 

should not be dried in the dryer.

•  Do not use fabric softeners and anti-static 

products unless they are recommended by 

the manufacturers of the fabric softener or 

the product.

•  This product must be grounded. 

Grounding installation decreases the risk of 

electric shock by opening a path with low 

resistance for the electricity flow in case of 

a malfunction or failure. Power cable of this 

product is equipped with a conductor and 

a grounding plug that allows for grounding 

the product. This plug must be installed 

appropriately and inserted into a socket 

which is grounded in accordance with the 

local laws and regulations.

•  Do not install the product behind a door 

with a lock, sliding door or a door that has 

a hinge against the hinge of the dryer.

•  Do not install or leave this product in 

places where it will be exposed to outdoor 

conditions.

•  Do not tamper with the controls.

•  Do not perform any repair or part replacing 

procedures on the product even if you 

know or have the ability to perform unless 

it is clearly suggested in the operating 

instructions or the published service 

manual.

•  Inside and exhaust duct of the product 

must be cleaned by the qualified service 

personnel periodically.

•  Wrong connection of grounding conductor 

of the product can cause electric shock. If 

you have any suspect about the grounding 

connection, have it checked by a qualified 

electrician, service representative or service 

personnel.