Blomberg TAF 7239 Manuale Utente

5 - EN

Refer to the nearest Authorised Service Agent 

for installation of your product.

C

Preparation of location and electrical 

installation for the product is under 

customer’s responsibility.

B

Installation and electrical connections must 

be carried out by a qualified personnel.

A

Prior to installation, visually check if the 

product has any defects on it. If so, do not 

have it installed. Damaged products will 

cause risks for your safety.

•  Install the product in an environment which 

has no risk of freezing and is in a stable 

and level position.

•  Operate your product in a well ventilated, 

dust-free environment.

•  Do not block the air ducts in front of and 

under the product with materials such as 

long pile rugs and wooden bands.

•  Do not place your product on a long pile 

rug or on similar surfaces.

•  Do not install the product behind a door 

with a lock, sliding door or a hinged door 

which can strike the product.

•  Once the product is installed, it should stay 

at the same place where its connections 

have been made. When installing the 

product, make sure that the rear wall of it 

does not touch anywhere (tap, socket, etc.) 

and also pay attention to install the product 

at a place where it will stay permanently.

B

Do not place the product on top of the 

power cable.

•  Keep at least 1.5 cm distance to walls of 

other furniture.

•  A special part (Part no: 295 970 0100) 

replacing the top trim must be provided 

and installed by the Authorised Service 

Agent in order to use the machine under a 

counter or in a cupboard. It should never 

be operated without the top trim.

•  Leave at least 3 cm of space between 

the side and rear walls of the product and 

the walls of the counter/cupboard when 

installing your product under a counter or in 

a cupboard.

•  A fitting device should be used between 

the two machines when installing above a 

washing machine. The bracket (Part no. 

296 280 0100 white/296 280 0200 grey) 

must be installed by the Authorised Service 

Agent.

•  Place the product on a firm floor. If it will be 

placed on top of a washing machine, the 

approximate weight of both machines may 

reach 180 kg when they are full. Therefore, 

the floor must be capable of carrying the 

load on it!

Ventilation hose allows exhaust air from inside 

the machine

Vented dryer has 1 air outlet.

Stainless sheet metal or aluminum pipes can 

be used instead of a hose. The pipe diameter 

should be minimum 10 cm.

Maximum hose and pipe lengths are given in 

the table below.

Hose

Pipe

Maximum length

4 m

5 m

1 elbow 45°

-1.0 m

-0.3 m

1 elbow 90°

-1.8 m

-0.6 m

1 elbow 90° short

-2.7 m

1 wall passage

-2.0 m

-2.0 m

C

Each elbow and other passages should 

be subtracted from the maximum length 

stated above.

To connect a ventilation hose;

1.  Connect the air outlet hose to the 

hose spacer piece by turning it 

counterclockwise.

2.  Make the hose passages as shown below.

C

Exhaust of humid air from the dryer into the 

room is inconvenient. It may damage the 

walls and furniture in the room.

C

The ventilation hose can be routed outdoors 

via a window or it can be connected to the 

air outlet in the bathroom.

C

Air outlet hose must be routed directly to the 

outdoors. There must be a limited number 

of elbows as not to hinder ventilation.

C

To prevent water accumulation in the hose, 

make sure that it is not folded on the floor.