Tascam SN29401376 Manuale Utente
Advanced Operations
En-51
Speaker Distance
Here you can specify the distance from each speaker to the
listening position so that the sound from each speaker
arrives at the listener’s ears as the sound designer intended.
listening position so that the sound from each speaker
arrives at the listener’s ears as the sound designer intended.
■
Unit
`
feet:
Distances can be set in feet. Range: 0.2ft to 30.0ft in
0.2 foot steps.
0.2 foot steps.
`
meters:
Distances can be set in meters. Range: 0.06m to
9.00m in 0.06 meter steps.
9.00m in 0.06 meter steps.
(The default setting varies from country to country.)
■
Left, Front High Left, Center, Front High Right,
Right, Surround Right, Surround Back Right,
Surround Back Left, Surround Left, Subwoofer
Right, Surround Right, Surround Back Right,
Surround Back Left, Surround Left, Subwoofer
`
Specify the distance from each speaker to your
listening position.
listening position.
Note
• Speakers that you set to “No” or “None” in
“Speaker Configuration” cannot be selected (
Level Calibration
Here you can adjust the level of each speaker with the
built-in test tone so that the volume of each speaker is the
same at the listening position.
built-in test tone so that the volume of each speaker is the
same at the listening position.
Note
• These settings cannot be calibrated in either of the following
cases:
– The “Audio TV Out” setting is set to “On” (
– The “Audio TV Out” setting is set to “On” (
– “HDMI Control(RIHD)” is set to “On” (
you’re listening through your TV speakers.
– The AV receiver is muted.
■
Left, Front High Left, Center
*1
, Front High Right,
Right, Surround Right, Surround Back Right,
Surround Back Left, Surround Left
Surround Back Left, Surround Left
`
–12dB to 0dB to +12dB in 1 dB steps.
■
Subwoofer
`
–15dB to 0dB to +12dB in 1 dB steps.
Note
• Speakers that you set to “No” or “None” in
“Speaker Configuration” cannot be selected (
*1
For the center speaker and subwoofer, the level settings made
by using the Quick Setup are saved in this menu (
by using the Quick Setup are saved in this menu (
Tip
• If you’re using a handheld sound level meter, adjust the level of
each speaker so that it reads 75 dB SPL at the listening position,
measured with C-weighting and slow reading.
measured with C-weighting and slow reading.
Main menu
Audio Adjust
With the Audio Adjust functions and settings, you can
adjust the sound and listening modes as you like.
adjust the sound and listening modes as you like.
Multiplex/Mono
■
Multiplex
Input Channel
`
Main
`
Sub
`
Main/Sub
This setting determines which channel of a stereo
multiplex source is output. Use it to select audio channels
or languages with multiplex sources, multilingual TV
broadcasts, and so on.
multiplex source is output. Use it to select audio channels
or languages with multiplex sources, multilingual TV
broadcasts, and so on.
■
Mono
Input Channel
`
Left + Right
`
Left
`
Right
This setting specifies the channel to be used for playing
any 2-channel digital source such as Dolby Digital, or 2-
channel analog/PCM source in the Mono listening mode.
any 2-channel digital source such as Dolby Digital, or 2-
channel analog/PCM source in the Mono listening mode.
This setting is set automatically by Audyssey 2EQ
®
Room Correction and Speaker Setup (
This setting is set automatically by Audyssey 2EQ Room
Correction and Speaker Setup (
Correction and Speaker Setup (
Audio Adjust
1
2
3
4
5
“Setup”