Technics SA-DA10 Manuale Utente
19
RQT5518
2
1
3
4
5
SA-DA10
SA-DA8
1
BALANCE
TOP MENU
DISPLAY
DVD
ENTER
MENU
STEREO
DELAY
SURROUND SFC
TEST
MUTING
DIMMER
VOL
TV VOL
TV/AV
1
2
3
DIRECT TUNING/
DISC ENTER
4
5
6
≥
10/–/– –
7
8
9
0
+
–
+
–
LEVEL
DISC/DECK
1/2
DVD 6CH
+
–
1
4
7
0
8
9
5
6
2
3
DIRECT TUNING/
DISC ENTER
VOLUME
MUTING
≥
10/ENTER
DISC/DECK 1/2
MD
SOUND MODE
SFC
SLOW/
SEARCH
DELAY
TOP MENU
ENTER
MENU
DISPLAY
RETURN
SUB TITLE AUDIO
ANGLE
+
–
LEVEL
TEST
GROUP
–
+
DIMMER
PAGE
-/--
DVD
2
3
4
5
3
4
5
2
5
2
TEST
TEST
SPEAKERS
A
B
BI-WIRE
VOL
+
–
+
–
VOLUME
LEVEL
LEVEL
+
–
+
–
SA-DA10
SA-DA8
SA-DA10
SA-DA8
SA-DA10
SA-DA8
SA-DA10
SA-DA8
SPEAKERS
A
L
C
R
RS
LS
SW
C
RS
LS
SW
Preparation
Preparatory steps
Adjusting speaker output level
Adjust speaker level so the output from all the speakers is the
same apparent level when sitting where you would normally enjoy
a source.
same apparent level when sitting where you would normally enjoy
a source.
1
Press [A] or [BI-WIRE] to turn on
SPEAKERS.
SPEAKERS.
A or BI-WIRE refer to the speaker terminals at the rear of
the unit.
You cannot adjust output level when SPEAKERS B is
selected.
the unit.
You cannot adjust output level when SPEAKERS B is
selected.
2
by remote control only
Press [TEST] to output the test signal.
“TEST” appears on the display.
The signal is output from each speaker in order for about
two seconds each:
L: Front speaker (left)
C: Center speaker
R: Front speaker (right)
RS: Surround speaker (right)
LS: Surround speaker (left)
SW: Subwoofer
Speakers set as “NONE” or “NO” are skipped.
The signal is output from each speaker in order for about
two seconds each:
L: Front speaker (left)
C: Center speaker
R: Front speaker (right)
RS: Surround speaker (right)
LS: Surround speaker (left)
SW: Subwoofer
Speakers set as “NONE” or “NO” are skipped.
Note
DSP sound mode switches to SURROUND mode when the
test starts.
test starts.
3
by remote control
Press [VOLUME (+ or –)] (SA-DA10) or
[VOL (– or +)] (SA-DA8) to set the
volume level normally used for
enjoying the source.
[VOL (– or +)] (SA-DA8) to set the
volume level normally used for
enjoying the source.
Note
Use [BALANCE] if the left right balance of the front
speakers is off.
speakers is off.
4
by remote control only
Press [LEVEL] to select the speaker
channel to adjust.
channel to adjust.
The current level appears on the display.
Press again to change the speaker channel.
Press again to change the speaker channel.
Speakers set as “NONE” or “NO” are skipped.
5
by remote control only
Press [+] or [–] to adjust the level to
the same apparent level as the front
speakers.
the same apparent level as the front
speakers.
The four channels can be adjusted between –10 dB and
+10 dB, with zero being the current level of the front
speakers.
+10 dB, with zero being the current level of the front
speakers.
6
Repeat 4 and 5 for each speaker
channel.
channel.
To stop the test signal
Press [TEST].
Note
The test signal will not be output if VGCA is ON (
a
page 27).