Land Pride RCRM2510 Manuale Utente
11
Section 1: Assembly and Set-Up
5/09/08
RCR2596, RCR2510 and RCRM2510 Rotary Cutters 312-753M
Land Pride
Lift Type Cutter 3-Point Assembly
Figure 1-3
the A-Frame hitch. Secure the A-Frame hitch with the
3/4" bolts (#15), 3/4" flat washer (#13) and 3/4" lock
nut (#12).
3/4" bolts (#15), 3/4" flat washer (#13) and 3/4" lock
nut (#12).
2.
Place the 2" long bushing (#17) between the A-
Frame hitch as shown and insert 1” bolt (#9) through
the hole in the hitch and bushing. Secure with the 1”
lock nut (#10).
Frame hitch as shown and insert 1” bolt (#9) through
the hole in the hitch and bushing. Secure with the 1”
lock nut (#10).
3.
Assemble the two short braces (#8) that are on the
rear brace (#1) between the back holes of the
A-Frame (#11) using the clevis pin (#18) provided
and secure with the flat washer (#21) and cotter pin
(#19).
rear brace (#1) between the back holes of the
A-Frame (#11) using the clevis pin (#18) provided
and secure with the flat washer (#21) and cotter pin
(#19).
4.
Assemble the two longer straight braces (#5) to the
front hole of the lug that is welded behind the
gearbox mount. Secure with the 1" bolt (#6) and lock
nut (#7).
front hole of the lug that is welded behind the
gearbox mount. Secure with the 1" bolt (#6) and lock
nut (#7).
5.
Assemble the formed rear braces (#2) to the inside of
the inner most lugs at the rear of the cutter. Secure
with the 3/4” bolt (#3) and lock nut (#4).
the inner most lugs at the rear of the cutter. Secure
with the 3/4” bolt (#3) and lock nut (#4).
6.
Install the other clevis pin (#18), flat washer (#21)
and cotter pin (#19) into the top front hole of the A-
Frame.
and cotter pin (#19) into the top front hole of the A-
Frame.
Driveline Installation
1.
Attach the slip-clutch end of the driveline (#16) to the
gearbox input shaft securely. Make certain that the
slip-clutch is fully onto the input shaft splines.
Tighten the conical dog pin on back side of slip-
clutch to 45-50 ft-lb torque.
gearbox input shaft securely. Make certain that the
slip-clutch is fully onto the input shaft splines.
Tighten the conical dog pin on back side of slip-
clutch to 45-50 ft-lb torque.
2.
Secure chain #20 to hole in driveline guard. Driveline
guard not shown.
guard not shown.
Gearbox Vent Plug
Refer to Figure 1-2
Gearbox vent plugs are shipped loose and packaged
with the Operator’s Manual. Remove existing splitter
gearbox pipe plug and replace with 3/8” vent plug.
Remove wing box pipe plugs and replace with 1/2” vent
plugs.
with the Operator’s Manual. Remove existing splitter
gearbox pipe plug and replace with 3/8” vent plug.
Remove wing box pipe plugs and replace with 1/2” vent
plugs.
Figure 1-2
Lift-Type Cutter
Hitch Assembly
Refer to Figure 1-3:
1.
Assemble the A-Frame hitch (#11) to the lower bolt
holes of the front inside hitch ears as shown. Insert
the 5/8" long bushings (#14) into the bottom holes of
holes of the front inside hitch ears as shown. Insert
the 5/8" long bushings (#14) into the bottom holes of
22320
1/2” Wing Box Pipe Plug
1/2” Wing Box
Pipe Plug
3/8” Splitter Box Pipe Plug
NOTE: Do not tighten hardware until assembly is
complete. Refer to “Torque Values Chart for
Common Bolt Sizes” on page 38.
complete. Refer to “Torque Values Chart for
Common Bolt Sizes” on page 38.
22289