Land Pride RCBM6610 Manuale Utente

Pagina di 66
25
Section 1: Assembly & Set-up
11/11/12
RCB6610 & RCBM6610 Series 2 S/N 944730+ Rotary Cutters   330-584M
Unhook Rotary Cutter
1.
See “Long Term Storage” on page 48 if parking the 
cutter for long periods and end of season. 
2.
Disengage PTO, park on a level hard surface. Place 
tractor gear selector in park or set park brake.
3.
Raise center deck fully up.
4.
Wait for blades to come to a complete stop and then 
fold wing up to transport position.
5.
Shut tractor engine off and remove switch key before 
dismounting from tractor.
Refer to Figure 1-25: 
6.
Place transport lock pin (#2) in transport lock 
holes (B). Make sure pin is secured with hairpin 
cotter (#3). 
7.
Remove stroke control spacers (#4) from center 
hydraulic cylinder.
8.
Start tractor and lower cutter until front skids are on 
the ground. 
9.
Shut tractor engine off and remove switch key before 
dismounting tractor.
10. Replace stroke control spacers (#4) on lift cylinder as 
needed to support wheels at this height.
11. Return to the tractor seat. With no one around or near 
the cutter, move cylinder lift levers back and forth to 
release hydraulic line pressure.
Refer to Figure 1-26:
12. Remove park jack (#3) from weight box and attach to 
jack mount (#12) as shown. Fully insert detent 
pin (#8) in jack mount to secure park jack. 
13. If needed, realign park jack (#3) to be vertical. Refer 
14. Unhook hydraulic hoses (#10 & #11) from tractor 
duplex outlets. Store coupling ends in hose 
holder (#14).
15. Unhook hitch safety chain (#4) from tractor.
16. Pull back on locking collar (#6) and pull driveline (#5) 
from tractor PTO shaft.
17. Collapse driveline (#5) by pushing tractor end of 
driveline toward the splitter gearbox.
18. Rotate driveline hanger (#7) up to position shown 
and store driveline on hanger. If height of driveline 
hanger needs readjusting, refer to “Adjust Driveline 
Hanger” 
on page 21.
19. Adjust park jack (#3) to raise cutter up until all load is 
removed from tractor drawbar.
20. Remove connecting hitch pin or bolt as follows:
a. Refer to Detail A in Figure 1-26: If unhooking 
LP Performance hitch or standard clevis, remove 
hairpin cotter (#2) and hitch pin (#1).
b. Refer to Figure 1-11 on page 17: If unhooking 
bar-tite hitch, remove lock nut (#2) and bolt (#1).
21. Restart tractor and drive tractor slowly forward 
several feet.
22. Shut tractor down properly before dismounting. 
23. Lower park jack (#3) until skid shoes support cutter.
24. Replace connecting pin/bolt (#1) as follows:
a. Refer to Detail A in Figure 1-26:
If unhooking LP Performance hitch, insert hitch 
pin (#1) in horizontal hitch holes to support clevis 
level. Secure with hairpin cotter (#2)
b. Refer to Detail B in Figure 1-26:
If unhooking standard clevis, replace connecting 
pin (#1) in clevis hitch pin holes and secure with 
hair pin cotter (#2).
c. See Figure 1-11 on page 17:
If unhooking bar-tite hitch, remove hitch (#10) 
from tractor and attach it to cutter hitch (#9) with 
bolt (#1) and lock nut (#2) Screw lock nut on 4 or 
5 full turns. Do not torque nut tight.
Wing Transport Lock
Figure 1-25
Unhook Rotary Cutter (LP Performance Hitch Shown)
Figure 1-26
30173
37986