Black & Decker CS1014 Manuale Utente

dust collection can reduce dust-related

hazards.

4) PoWeR tool uSe ANd cARe

a) do not force the power tool. use the

correct power tool for your application.

The correct power tool will do the job better and

safer at the rate for which it was designed.

b) do not use the power tool if the switch

does not turn it on and off. Any power tool

that cannot be controlled with the switch is

dangerous and must be repaired.

c) disconnect the plug from the power

source and/or the battery pack from

the power tool before making any

adjustments, changing accessories,

or storing power tools. Such preventive

safety measures reduce the risk of starting

the power tool accidentally.

d) Store idle power tools out of the reach

of children and do not allow persons

unfamiliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. check for

misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the power tool’s operation.

If damaged, have the power tool repaired

before use. Many accidents are caused by

poorly maintained power tools.

f) keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are

easier to control.

g) use the power tool, accessories and

tool bits, etc. in accordance with these

instructions, taking into account the

working conditions and the work to

be performed. Use of the power tool for

operations different from those intended

could result in a hazardous situation.

5) SeRvIce

a) have your power tool serviced by a

qualified repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

Safety inStructionS for all SawS

dANGeR: keep hands away from

cutting area and the blade. keep your

second hand on auxiliary handle or

motor housing. If both hands are holding

the saw, they cannot be cut by the blade.

b) do not reach underneath the

workpiece. The guard cannot protect you

from the blade below the workpiece.

c) Adjust the cutting depth to the

thickness of the workpiece. Less than a

full tooth of the blade teeth should be visible

below the workpiece.

d) Never hold piece being cut in your

hands or across your leg. Secure the

workpiece to a stable platform. It is

important to support the work properly to

minimize body exposure, blade binding, or

loss of control.

e) hold power tool by insulated gripping

surfaces when performing an operation

where the cutting tool may contact

hidden wiring or its own cord. Contact

with a “live” wire will also make exposed

metal parts of the power tool “live” and

shock the operator.

f) When ripping always use a rip fence

or straight edge guide. This improves the

accuracy of cut and reduces the chance of

blade binding.

g) Always use blades with correct size

and shape (diamond versus round) of

arbour holes. Blades that do not match

the mounting hardware of the saw will run

eccentrically, causing loss of control.

h) Never use damaged or incorrect blade

washers or bolt. The blade washers and

bolt were specially designed for your saw,

for optimum performance and safety of

operation.

cAuSeS ANd oPeRAtoR

PReveNtIoN of kIckbAck:

• Kickback is a sudden reaction to a

pinched, bound or misaligned saw blade,

causing an uncontrolled saw to lift up and

out of the workpiece toward the operator.

• When the blade is pinched or bound tightly

by the kerf closing down, the blade stalls

and the motor reaction drives the unit rapidly

back toward the operator.

• If the blade becomes twisted or misaligned

in the cut, the teeth at the back edge of the

blade can dig into the top surface of the

wood causing the blade to climb out of the

kerf and jump back toward the operator.
Kickback is the result of saw misuse and/or

incorrect operating procedures or conditions

and can be avoided by taking proper

precautions as given below:
a) Maintain a firm grip with both hands

on the saw and position your arms to

resist kickback forces. Position your

body to either side of the blade, but not

in line with the blade. Kickback could

cause the saw to jump backwards, but

kickback forces can be controlled by the

operator, if proper precautions are taken.

b) When blade is binding, or when

interrupting a cut for any reason, release