FieldServer FCI E3 Series Manuale Utente
FS-8700-132 Gamewell FCI-E3 Driver Manual
Page 19 of 20
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com
Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com
Appendix B.1.
Driver Stats Exposed.
In addition to the standard FieldServer operating statistics the driver exposes certain key stats in a
Data Array if required. An upstream device can then monitor these stats.
Add the following to your configuration file to activate these stats.
Data Array if required. An upstream device can then monitor these stats.
Add the following to your configuration file to activate these stats.
// Expose Driver Operating Stats.
Data_Arrays
Data_Array_Name,
Data_Format,
Data_Array_Length
fci-e3-stats,
UINT32,
200
The driver exposes stats based on a port handle. The offset specified in the table below must be
added to the handle number multiplied by 100. i.e. for port whose handle is 1 then the driver will store
the 1
st
stat at 1+100*1=101.
Stat
Offset Description
#define FCI_E3_STAT_NO_PLACE_TO_STORE
1
Increments each time point data is
received but there is no Map
Descriptor to store the data (any)
received but there is no Map
Descriptor to store the data (any)
#define
FCI_E3_STAT_NO_PLACE_TO_STORE_ZONE
FCI_E3_STAT_NO_PLACE_TO_STORE_ZONE
2
Increments each time point data is
received but there is no Map
Descriptor to store Zone data
received but there is no Map
Descriptor to store Zone data
#define
FCI_E3_STAT_NO_PLACE_TO_STORE_RELAY
FCI_E3_STAT_NO_PLACE_TO_STORE_RELAY
3
Increments each time point data is
received but there is no Map
Descriptor to store Relay data
received but there is no Map
Descriptor to store Relay data
#define
FCI_E3_STAT_NO_PLACE_TO_STORE_LOOP
FCI_E3_STAT_NO_PLACE_TO_STORE_LOOP
4
Increments each time point data is
received but there is no Map
Descriptor to store the Loop data
received but there is no Map
Descriptor to store the Loop data
#define
FCI_E3_STAT_NO_PLACE_TO_STORE_SENSOR
FCI_E3_STAT_NO_PLACE_TO_STORE_SENSOR
5
Increments each time point data is
received but there is no Map
Descriptor to store the Sensor
data
received but there is no Map
Descriptor to store the Sensor
data
#define
FCI_E3_STAT_NO_PLACE_TO_STORE_MODULE
FCI_E3_STAT_NO_PLACE_TO_STORE_MODULE
6
Increments each time point data is
received but there is no Map
Descriptor to store the Module
data
received but there is no Map
Descriptor to store the Module
data
#define FCI_E3_STAT_EMPTY_MSG
7
Number of times that a message
line
line
was
zero
bytes
long
(excluding the terminator)
#define FCI_E3_STAT_SHORT_MSG
8
Number of times that a message
line was too short probably a
system id tag line
line was too short probably a
system id tag line
#define FCI_E3_STAT_NO_RESET
9
Increments each time a reset was
rcvd but no Data Array was reset
rcvd but no Data Array was reset
#define
FCI_E3_STAT_NO_PLACE_TO_STORE_PANEL
FCI_E3_STAT_NO_PLACE_TO_STORE_PANEL
10
Increments each time point data is
received but there is no Map
Descriptor to store data that
cannot be attributed to a zone,
relay, loop, sensor, module
received but there is no Map
Descriptor to store data that
cannot be attributed to a zone,
relay, loop, sensor, module
#define FCI_E3_STAT_RCVD_MSGS
11
Increments each time a message
is received
is received