FieldServer FCI E3 Series Manuale Utente
FS-8700-132 Gamewell FCI-E3 Driver Manual
Page 17 of 20
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com
Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com
Appendix B. Driver Error Messages.
Message
Description
FCI_E3:#1 FYI. Use a DA called <%s> to expose
diagnostic info., FCI_E3_STATS_DA )
diagnostic info., FCI_E3_STATS_DA )
Refer to Appendix B.1
FCI_E3:#2 FYI. Added Event Desc=<%s> Index=%d
Categ=%d
Categ=%d
,
new_event_desc
,
new_event_desc_index_value , new_event_desc_categ ) ;
Printed for information only. No action
required if it confirms your expectations.
required if it confirms your expectations.
FCI_E3:#3 Err. No space. Reject Event Desc=<%s>
Index=%d
Index=%d
,
new_event_desc
,
new_event_desc_index_value ) ;
There is only space for 60 event types.
4
FCI_E3:#4
FYI.
Duplicate
Event
Desc=<%s>.
,
new_event_desc ) ;
FCI_E3:#5
FCI_E3:#5
FYI.
Duplicate
Event
Desc=<%s>.
,
new_event_desc ) ;
The Event type being added already
exists. If you are updating the category,
ignore the message. Otherwise correct the
configuration file.
exists. If you are updating the category,
ignore the message. Otherwise correct the
configuration file.
4
FCI_E3:#6 Err. Event Index=%d. Too big to set bit.,
drv_bd->event_index )
drv_bd->event_index )
If the event index is greater than 64 then
the data cannot be stored as bits - only 64
bits are reserved for events.
the data cannot be stored as bits - only 64
bits are reserved for events.
FCI_E3:#7a Err. DA=%s too short. Rqd=%d, dt-
>buffer_name , offset );
FCI_E3:#7b Err. DA=%s too short. Rqd=%d, possible_md-
>data->buffer_name , offset );
>buffer_name , offset );
FCI_E3:#7b Err. DA=%s too short. Rqd=%d, possible_md-
>data->buffer_name , offset );
The MD in question has a length and
offset which makes it run past the end of
the Data Array. Message 7b is printed
when data is being stored as bits.
offset which makes it run past the end of
the Data Array. Message 7b is printed
when data is being stored as bits.
4
FCI_E3:#8 FYI. Reset was rcvd and processed! Stamped
%s %s , drv_bd->time , drv_bd->date )
%s %s , drv_bd->time , drv_bd->date )
Printed for information only. No action
required.
required.
FCI_E3:#9 Err. Reset was ignored.
A reset was received but the driver could
not reset any data. 'Clear_on_Reset'
possibly set to 'no' on all Map Descriptors?
not reset any data. 'Clear_on_Reset'
possibly set to 'no' on all Map Descriptors?
FCI_E3:#10 FYI. Reset of DA=%s Off=%d Len=%d,
possible_md->data->buffer_name
possible_md->data->buffer_name
,
possible_md-
>bxi_data_buffer_offset , possible_md->data_length );
Printed for information only. No action
required.
required.
FCI_E3:#11 Err. Cant reset DA=%s len=%d rqd=%d,
possible_md->data->buffer_name
possible_md->data->buffer_name
,
da_get_length_in_items ( (DAH_TYP) possible_md->data )
,
,
possible_md->data_length+possible_md-
>bxi_data_buffer_offset );
The Map Descriptor in question has a
length and offset which makes it run past
the end of the Data Array.
length and offset which makes it run past
the end of the Data Array.
4
FCI_E3:#12a Err. No MD's to store message data.
FCI_E3:#12b Err. No MD's to store message data."
FCI_E3:#13 Err. Msg was ignored. MD Required for
Storage.
Storage.
The Driver could not find a place to store
data from a message received. If the data
is not required then the message may be
ignored.
data from a message received. If the data
is not required then the message may be
ignored.
Otherwise
update
the
configuration file
4
.
FCI_E3:#13a Err. Diagnostic 1);
FCI_E3:#13b Err. Diagnostic 2);
FCI_E3:#13c Err. Diagnostic 3);
FCI_E3:#13b Err. Diagnostic 2);
FCI_E3:#13c Err. Diagnostic 3);
Take a log. Try and repeat the event that
caused the message to be printed. Then
contact tech support.
caused the message to be printed. Then
contact tech support.
FCI_E3:#14
Err.
<%s>
file
not
found.,
md-
>mapdesc_name ) ;
FCI_E3:#15 Err. Event Type=<%s> Not recognized." ,
drv_bd->event_desc )
FCI_E3:#16 Err. Point Type='%c'(%#x) Not recognized. ,
drv_bd->point_identifier[0] , drv_bd->point_identifier[0] ) ;
FCI_E3:#15 Err. Event Type=<%s> Not recognized." ,
drv_bd->event_desc )
FCI_E3:#16 Err. Point Type='%c'(%#x) Not recognized. ,
drv_bd->point_identifier[0] , drv_bd->point_identifier[0] ) ;
If this error is repeated often it is possible
that a FCI firmware update has made the
driver unusable. Take a log and contact
tech support.
that a FCI firmware update has made the
driver unusable. Take a log and contact
tech support.
4
Correct the configuration file, download to the FieldServer and restart the FieldServer for the changes to
take effect.