Grizzly G0644 Manuale Utente

Pagina di 52
-30-
G0644  15" Open-End Wide Belt Sander
Motor & Electrical (continued)
Symptom
Possible Cause
Possible Solution
Motor  stalls  or  is 
overloaded.
1.  Sanding depth too aggressive.
2.  Workpiece  material  is  not  suitable  for  this 
machine.
3.  Conveyor speed too fast for task.
4.  Dust collection ducting is poor.
5.  Air pressure brake solenoid is at fault.
6.  Run capacitor is at fault.
7.  Conveyor speed dial is at fault.
8.  Motor connection is wired incorrectly.
9.  Plug/receptacle is at fault.
10. Motor bearings are at fault.
11. Machine is undersized for the task.
12. Motor has overheated.
13. Contactor not getting energized or has poor 
contacts.
14. Motor is at fault.
15. Centrifugal switch is at fault.
1.  Reduce sanding depth or install coarser sandpaper.
2.  Only sand wood products; make sure moisture con-
tent is below 20% and there are no foreign materials 
in the workpiece.
3.  Decrease conveyor speed (feed rate).
4.  Seal all leaks, size ducts correctly, eliminate bends, 
and refer to Dust Collection Basics Handbook (ISBN 
0-9635821-2-7) for further recommendations.
5.  Test/replace.
6.  Test/replace.
7.  Test and replace if faulty.
8.  Correct motor wiring connections.
9.  Test for good contacts; correct the wiring.
10. Test by rotating shaft; rotational grinding/loose shaft 
requires bearing replacement.
11. Use new sandpaper with appropriate grit; reduce the 
feed rate/depth of sanding.
12. Clean off motor, let cool, and reduce workload.
13. Test for power on all legs and contactor operation. 
Replace if faulty.
14. Test/repair/replace.
15. Adjust/replace centrifugal switch if available.
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
Grit rubs off the belt 
easily.
1.  Sanding  belt  has  been  stored  in  an  incor-
rect environment.
2.  Sanding belt has been folded or smashed.
1.  Store  sanding  belt  away  from  extremely  dry  or  hot 
temperatures.
2.  Store sanding belt flat, not folded or bent.
Sanding  surfaces 
clog quickly or burn.
1.  Sanding depth too aggressive.
2.  Sanding softwood.
1.  Reduce sanding depth or install coarser sandpaper.
2.  Use  different  stock.  Or,  accept  the  characteristics 
of  the  stock  and  plan  on  cleaning/replacing  belts 
frequently.
Burn 
marks 
on 
workpiece.
1.  Using too fine of sanding grit.
2.  Sanding depth too aggressive.
3.  Work held still for too long.
1.  Use a coarser grit sanding belt.
2.  Reduce sanding depth or install coarser sandpaper.
3.  Do not keep workpiece in one place for too long.
Glazed  sanding  sur-
faces.
1.  Sanding wet stock.
2.  Sanding stock with high residue.
1.  Dry stock properly before sanding.
2.  Use  different  stock.  Or,  accept  the  characteristics 
of the stock and plan on cleaning/replacing sanding 
belts frequently.
Workpiece  slips  on 
conveyor belt.
1.  Dirty conveyor belt.
2.  Conveyor belt is worn.
1.  Clean conveyor belt.
2.  Replace conveyor belt.
Uneven  thickness 
from  left  to  right  of 
board.
1.  Sanding drum not parallel to conveyor.
2.  Conveyor belt is worn. 
1.  Adjust  the  conveyor  to  sanding  drum  parallelism 
(
Page 32).
2.  Replace conveyor belt.
Machine  is  loud, 
overheats  or  bogs 
down in the cut.
1.  Excessive depth of cut.
2.  Dull sanding belt.
1.  Decrease depth of cut.
2.  Replace sanding belt.
Sanding Operation