Grizzly G0664 Manuale Utente
g0664 heavy duty Metal-Cutting Bandsaw
-37-
Blade Breakage
Many conditions may cause a bandsaw blade to
break. Blade breakage is unavoidable, in some
cases, since it is the natural result of the peculiar
stresses that bandsaw blades must endure. Blade
breakage is also due to avoidable circumstances.
avoidable blade breakage is most often the result
of poor care or judgement on the part of the
operator when mounting or adjusting the blade or
support guides.
break. Blade breakage is unavoidable, in some
cases, since it is the natural result of the peculiar
stresses that bandsaw blades must endure. Blade
breakage is also due to avoidable circumstances.
avoidable blade breakage is most often the result
of poor care or judgement on the part of the
operator when mounting or adjusting the blade or
support guides.
The most common causes of blade breakage
are:
•
Faulty alignment or adjustment of the blade
guides.
guides.
•
Feeding the blade too fast.
•
dull or damaged teeth.
•
over-tensioned blade.
•
top blade guide assembly set too high above
the workpiece. adjust the top blade guide
assembly so that there is approximately ½"
between the bottom of the assembly and the
workpiece.
the workpiece. adjust the top blade guide
assembly so that there is approximately ½"
between the bottom of the assembly and the
workpiece.
•
using a blade with a lumpy or improperly fin-
ished braze or weld.
ished braze or weld.
•
Continuously running the bandsaw when not
in use.
in use.
•
leaving the blade tensioned when not in
use.
use.
•
using the wrong pitch (tpi) for the workpiece
thickness. the general rule of thumb is to
have at least two teeth in contact with the
workpiece at all times during cutting.
thickness. the general rule of thumb is to
have at least two teeth in contact with the
workpiece at all times during cutting.
Workpiece
Inspection
some metal workpieces are not safe to cut with a
metal cutting bandsaw; instead, a different tool or
machine should be used.
metal cutting bandsaw; instead, a different tool or
machine should be used.
Before cutting, inspect the material for any of
the following conditions and take the neces-
sary precautions:
•
Small or Thin Workpieces: small or thin
workpieces may be damaged during cut-
ting—avoid cutting these workpieces if possi-
ble. if you must cut a small or thin workpiece,
attach it to or clamp it between larger scrap
pieces that will both support the workpiece
through the cut. some thin sheet metals will
not withstand the forces from this bandsaw
during cutting; instead, use a shear, nibblers,
or sheet metal nippers to cut these pieces.
workpieces may be damaged during cut-
ting—avoid cutting these workpieces if possi-
ble. if you must cut a small or thin workpiece,
attach it to or clamp it between larger scrap
pieces that will both support the workpiece
through the cut. some thin sheet metals will
not withstand the forces from this bandsaw
during cutting; instead, use a shear, nibblers,
or sheet metal nippers to cut these pieces.
•
Unstable Workpieces: Workpieces that can-
not be properly supported or stabilized with
the vise should not be cut on this bandsaw.
examples are chains, cables, workpieces
with internal or built-in moving or rotating
parts, etc.
not be properly supported or stabilized with
the vise should not be cut on this bandsaw.
examples are chains, cables, workpieces
with internal or built-in moving or rotating
parts, etc.
•
Material Hardness: always factor in the hard-
ness of the metal before cutting it. hardened
metals will take longer to cut, may require
lubrication, and may require a different type
of blade in order to efficiently cut them.
ness of the metal before cutting it. hardened
metals will take longer to cut, may require
lubrication, and may require a different type
of blade in order to efficiently cut them.
•
Tanks, Cylinders, Containers, Valves, Etc:
Cutting into containers that are pressur-
ized or contain gasses or liquids can cause
explosions, fires, caustic burns, or machine
damage. avoid cutting any of these types of
containers unless you have verified that the
container is empty and it can be properly sup-
ported during a cut.
Cutting into containers that are pressur-
ized or contain gasses or liquids can cause
explosions, fires, caustic burns, or machine
damage. avoid cutting any of these types of
containers unless you have verified that the
container is empty and it can be properly sup-
ported during a cut.
•
Magnesium: pure magnesium burns eas-
ily. Cutting magnesium with a dull blade can
create enough friction to ignite the small
magnesium chips. avoid cutting magnesium
if possible.
ily. Cutting magnesium with a dull blade can
create enough friction to ignite the small
magnesium chips. avoid cutting magnesium
if possible.