Maytag MCS 16021937 Manuale Utente
I
NSTALLATION
I
NSTRUCTIONS
,
CONT
.
TO INSTALL PANELS:
1. Perform the handle removal
instructions in How to Install and
Remove the Handles, including
instructions to remove mounting
posts from door face.
Remove the Handles, including
instructions to remove mounting
posts from door face.
2. Remove top door trim.
3. Remove handle side door trim.
4. Slide panel in the handle side of door,
by using grooves provided by bottom
door cap and side door trim.
door cap and side door trim.
5. Replace mounting posts, handles, and
trim.
TO REMOVE PANELS:
1. Perform the handle removal
instructions in How to Install and
Remove the Handles, including
instructions to remove mounting
posts from door face.
Remove the Handles, including
instructions to remove mounting
posts from door face.
2. Remove top door trim.
3. Remove handle side door trim.
4. Slide panel out the handle side of
door.
H
OW TO
R
EPLACE THE
D
OOR AND
H
INGES
1. Install center hinge with Phillips
screws.
2. Install stabilizing brackets with
3
⁄
8
" hex
head screws.
3. Replace center
hinge pin.
4. Place hinge side of
refrigerator door on center hinge pin.
5. While holding
refrigerator door
upright,
upright,
tighten
down top hinge
with
with
5
⁄
16
" hex head
driver.
6. Install top door trim of fresh food
door with a Phillips screwdriver.
To avoid personal injury or property
damage, fresh food panel should not
weigh more than 30 lbs (14 kgs) and
freezer panel should not weigh more
than 15 lbs (7 kgs).
damage, fresh food panel should not
weigh more than 30 lbs (14 kgs) and
freezer panel should not weigh more
than 15 lbs (7 kgs).
H
OW TO
I
NSTALL AND
R
EMOVE
P
ANELS
(SOME MODELS)
WARNING:
6
Note:
If fresh food door is being reversed,
install alternate top hinge from
literature assembly.
install alternate top hinge from
literature assembly.
W
HAT IF
I
AM
I
NSTALLING
R
AISED
P
ANELS
?
Please see recommended dimensions for
paneling. All panel holes are
paneling. All panel holes are
1
⁄
4
" diameter.
29.982"
76.2 cm
42.060"
106.8 cm
6.039"
15.3 cm
2.879"
7.3 cm
6.269"
15.9 cm
2.964"
7.5 cm
23.563"
59.9 cm
23.810"
60.5 cm
36.100"
91.7 cm
36.100"
91.7 cm
H
OW
D
O
I M
OUNT
H
ANDLES
O
N
R
AISED
P
ANELS
?
The refrigerator is shipped with the
handle mounting posts attached to the
door with
handle mounting posts attached to the
door with
1
⁄
4
" hex head screw that is
approximately 1
1
⁄
2
" long. This length is
necessary to safely secure the mounting
post to the door.
post to the door.
If handles are being mounted to a raised
surface, the factory supplied hex head
screws will have to be replaced with a
longer version. To determine how long
the replacement screw must be, add the
thickness of the raised panel to the 1
surface, the factory supplied hex head
screws will have to be replaced with a
longer version. To determine how long
the replacement screw must be, add the
thickness of the raised panel to the 1
1
⁄
2
"
measurement. See example below.
1
1
⁄
2
" long
1
⁄
4
" hex
head screw (factory
installed)
installed)
1" thick raised
panel = 2
panel = 2
1
⁄
2
" long
1
⁄
4
" hex head screw