Beko LX 5053 S Manuale Utente
EN
11
REPOSITIONING THE DOOR
Follow the step by step instructions and the diagram below. Numbers in brackets
refer to diagrams.
refer to diagrams.
1. Switch off at the socket outlet and pull
out the mains plug.
2. Remove all food, loose items and fittings
from inside the appliance and door shelves.
3. Carefully tilt the appliance on its back
side. (1) (You may need somebody to
help you.) Take care not to damage the
appliance by laying on some protective
material (e.g. its original packaging). Make
sure that you tilt the appliance on its
back side, otherwise compressor oil may
block the pipes and you may damage the
appliance.
4. Unscrew and remove the LHS front feet
and bolt (2).
5. Unscrew the bolts and remove the
bottom hinge while holding the door (3).
6. Remove the door carefully from the top
hinge by sliding down wards (4).
7. Reposition top hinge bushing and
blanking plug on the opposite side and
stand the door safely (5). You may find it
easier to remove the bushing and the plug
with the tip of a small screwdriver. Take
care not to mark the door.
8. Reposition the top hinge on the opposite
side (6 and 7).
9. To refit the door, locate the top hinge in
the door, attach to the cabinet and hold the
door (8).
10. Fit the bottom hinge (9). If necessary
adjust and then tighten the bolts. Ensure,
that the door opens and closes easily and
that there are no gaps allowing air into the
cabinet. If there are gaps between the door
seal and the cabinet,adjust the door seal
out the mains plug.
2. Remove all food, loose items and fittings
from inside the appliance and door shelves.
3. Carefully tilt the appliance on its back
side. (1) (You may need somebody to
help you.) Take care not to damage the
appliance by laying on some protective
material (e.g. its original packaging). Make
sure that you tilt the appliance on its
back side, otherwise compressor oil may
block the pipes and you may damage the
appliance.
4. Unscrew and remove the LHS front feet
and bolt (2).
5. Unscrew the bolts and remove the
bottom hinge while holding the door (3).
6. Remove the door carefully from the top
hinge by sliding down wards (4).
7. Reposition top hinge bushing and
blanking plug on the opposite side and
stand the door safely (5). You may find it
easier to remove the bushing and the plug
with the tip of a small screwdriver. Take
care not to mark the door.
8. Reposition the top hinge on the opposite
side (6 and 7).
9. To refit the door, locate the top hinge in
the door, attach to the cabinet and hold the
door (8).
10. Fit the bottom hinge (9). If necessary
adjust and then tighten the bolts. Ensure,
that the door opens and closes easily and
that there are no gaps allowing air into the
cabinet. If there are gaps between the door
seal and the cabinet,adjust the door seal
by gently pulling away from the door using
fingers.
11. Fit the other front feet (10).
12. Carefully stand your appliance. (You
may need somebody to help you.)
Adjust the front feet (See Installation
Instructions)
13. Put back all, loose items and fittings.
14. Wait for at least 4 hours to allow the
system to settle before switching on.
Spare plastic parts supplied with the
appliance are for your future use during
door repositioning.
fingers.
11. Fit the other front feet (10).
12. Carefully stand your appliance. (You
may need somebody to help you.)
Adjust the front feet (See Installation
Instructions)
13. Put back all, loose items and fittings.
14. Wait for at least 4 hours to allow the
system to settle before switching on.
Spare plastic parts supplied with the
appliance are for your future use during
door repositioning.