Snapper YZ13331be Manuale Utente
11
Section 3 - MAINTENANCE
3.2.3. CHECK MOWER DRIVE BELT
1. Footrest Removal
1. Footrest Removal
a. Squeeze the deck lift handle and the release
lever and lift the deck lift handle until it locks in the
top notch which is the high cut/transport position.
b. Remove retaining knobs located at the corners
of footrest. Remove footrest. See Figure 3.3.
c. Check mower belt. If belt is frayed, slit, severed
or belt strands exposed, replace belt before
operating mower.
d. Reinstall footrest cover and reinstall knobs and
tighten securely.
lever and lift the deck lift handle until it locks in the
top notch which is the high cut/transport position.
b. Remove retaining knobs located at the corners
of footrest. Remove footrest. See Figure 3.3.
c. Check mower belt. If belt is frayed, slit, severed
or belt strands exposed, replace belt before
operating mower.
d. Reinstall footrest cover and reinstall knobs and
tighten securely.
FIGURE 3.3
2. Checking Mower Belt Tension
The idler and spring provide proper belt tension and
require no adjustment. If belt is frayed, slit, severed
or belt strands exposed, replace belt before
operating mower.
require no adjustment. If belt is frayed, slit, severed
or belt strands exposed, replace belt before
operating mower.
3.2.4. CHECK TRANSAXLE DRIVE BELTS
1. Checking Transaxle Belt Tension
The transaxle drive belts require no adjustment. If
belts are frayed, slit, severed or belt strands
exposed, replace belt before operating mower.
belts are frayed, slit, severed or belt strands
exposed, replace belt before operating mower.
3.3 AFTER EVERY 25 OPERATING HOURS
3.3.1. ENGINE
1. Engine Cooling System
The engine cooling system consists of an engine
shroud and engine fins. These should be kept clean
and free of debris as needed or cleaned.
2. Engine Oil
Change engine oil. See Section on CHANGE ENGINE
OIL. Refer to engine owner’s manual for oil
specifications.
3. Oil Filter
Change engine oil filter. Refer to engine owner’s
manual for filter specifications.
4. Air Filter
Refer to engine owner’s manual for service
instructions.
5. Fuel Filter
Refer to engine owner’s manual for service
instructions.
3.3.2. MOWER
1. Engine Cooling System
The engine cooling system consists of an engine
shroud and engine fins. These should be kept clean
and free of debris as needed or cleaned.
2. Engine Oil
Change engine oil. See Section on CHANGE ENGINE
OIL. Refer to engine owner’s manual for oil
specifications.
3. Oil Filter
Change engine oil filter. Refer to engine owner’s
manual for filter specifications.
4. Air Filter
Refer to engine owner’s manual for service
instructions.
5. Fuel Filter
Refer to engine owner’s manual for service
instructions.
3.3.2. MOWER
COMPONENTS
1. Mower Drive Belt
Check belt for proper tension. No adjustment required.
Replace belt as needed.
2. Mower Blade
Check blade for sharpness, wear, damage, and
torque. See the section on Mower Blade
Replacement/Repair.
3. Mower Deck Levelness
Check mower deck for proper levelness. Adjust as
required. See section on Mower Deck Adjustment -
Levelness.
Check belt for proper tension. No adjustment required.
Replace belt as needed.
2. Mower Blade
Check blade for sharpness, wear, damage, and
torque. See the section on Mower Blade
Replacement/Repair.
3. Mower Deck Levelness
Check mower deck for proper levelness. Adjust as
required. See section on Mower Deck Adjustment -
Levelness.
WARNING
Lifting or lowering the machine onto or down from
the rear bumper unassisted can cause severe injury.
Always have assistance from another person when
supporting the weight of machine.
the rear bumper unassisted can cause severe injury.
Always have assistance from another person when
supporting the weight of machine.
4. Cleaning Mower Deck
a. Make sure fuel cap is on tight. Turn fuel shut
off valve (If equipped) to the “CLOSED” position.
Start engine and allow it to run until engine runs
out of fuel. Close vent on fuel filler cap. See
Figure 2.3, Page 6.
b. Remove key from ignition switch.
c. Remove spark plug wire(s) and secure away
from spark plug(s).
d. Carefully stand YARD CRUISER on rear
bumper.
e. Clean underside of mower deck, removing all
accumulation of grass clippings and debris.
f. Lower YARD CRUISER to ground. Clean top
of deck, removing all grass clippings and debris.
off valve (If equipped) to the “CLOSED” position.
Start engine and allow it to run until engine runs
out of fuel. Close vent on fuel filler cap. See
Figure 2.3, Page 6.
b. Remove key from ignition switch.
c. Remove spark plug wire(s) and secure away
from spark plug(s).
d. Carefully stand YARD CRUISER on rear
bumper.
e. Clean underside of mower deck, removing all
accumulation of grass clippings and debris.
f. Lower YARD CRUISER to ground. Clean top
of deck, removing all grass clippings and debris.
DECK LIFT HANDLE
RELEASE
LEVER
LEVER
HIGH CUT/
TRANSPORT
NOTCH
TRANSPORT
NOTCH
FOOTREST
RETAINING
KNOBS
RETAINING
KNOBS