Snapper E331523KVE Manuale Utente
21
Section 4 - ADJUSTMENTS & REPAIR
WARNING
DO NOT attempt any adjustments, maintenance,
service or repairs with the engine running. Stop
engine. Stop blade. Engage parking brake. Remove
key. Remove spark plug wire from spark plug and
secure away from plug. Engine and components are
HOT. Avoid serious burns, allow all parts to cool
before working on machine. Fuel Filler Cap and Vent
must be closed securely to prevent fuel spillage.
Once blade is disengaged, it should come to a
complete stop in 3 seconds or less. If the blade
continues to rotate after 3 seconds, the blade brake
must be adjusted. Refer to Section “BLADE BRAKE
ADJUSTMENT” for adjustment procedures or return
machine to an authorized SNAPPER dealer for
adjustment. DO NOT CONTINUE to operate machine
until blade brake is adjusted and functioning
properly.
service or repairs with the engine running. Stop
engine. Stop blade. Engage parking brake. Remove
key. Remove spark plug wire from spark plug and
secure away from plug. Engine and components are
HOT. Avoid serious burns, allow all parts to cool
before working on machine. Fuel Filler Cap and Vent
must be closed securely to prevent fuel spillage.
Once blade is disengaged, it should come to a
complete stop in 3 seconds or less. If the blade
continues to rotate after 3 seconds, the blade brake
must be adjusted. Refer to Section “BLADE BRAKE
ADJUSTMENT” for adjustment procedures or return
machine to an authorized SNAPPER dealer for
adjustment. DO NOT CONTINUE to operate machine
until blade brake is adjusted and functioning
properly.
4.1 ENGINE ADJUSTMENTS & REPAIR
Refer to the engine owner’s manual for those
adjustments and/or repairs that can be made by the
owner.
adjustments and/or repairs that can be made by the
owner.
4.2 MOWER DECK & COMPONENT ADJUSTMENTS
The following mower deck and component
adjustments and repairs can be made by the owner.
However, if there is difficulty in achieving these
adjustments and repairs, it is recommended that
these repairs be made by an authorized SNAPPER
dealer.
adjustments and repairs can be made by the owner.
However, if there is difficulty in achieving these
adjustments and repairs, it is recommended that
these repairs be made by an authorized SNAPPER
dealer.
4.2.1. BLADE BRAKE ADJUSTMENT
The automatic Blade Brake should stop the blades
within 3 seconds anytime the blades are
disengaged by moving blade lever to the "OFF"
position or by releasing the Blade Pedals. When
the Blade Brake is properly adjusted there should
be 3” to 3-1/4" clearance between the Blade
Engagement Lever and the edge of the Latch
Plate. Check this by disengaging the Blade Lever
as shown in Figure 4.1. Perform the following
measurement and adjustment.
1. With the blade engagement lever disengaged,
measure the distance between the front of the
blade lever and the edge of the latch plate. The
dimension should be 3” to 3-1/4" clearance
between lever and edge of plate. See Figure 4.1.
If the dimension is incorrect go to step 2.
2. Remove Belt Cover. Refer to Section “BLADE
BELT COVER REMOVAL”.
3. If dimension is greater than 3-1/4”, rotate nut
clockwise to increase brake tension. If dimension
is less than 3”, rotate nut counter-clockwise to
decrease brake tension. See Figure 4.2.
4. Reinstall belt cover and tighten bolts securely.
WARNING
DO NOT operate machine until blade brake is
adjusted and functioning properly. If blade stop time
can not be achieved with the adjustment procedure
described above, take machine immediately to an
authorized Snapper dealer.
adjusted and functioning properly. If blade stop time
can not be achieved with the adjustment procedure
described above, take machine immediately to an
authorized Snapper dealer.
FIGURE 4.1
FIGURE 4.2
ROTATE NUT CLOCKWISE TO
INCREASE BRAKE TENSION.
ROTATE NUT COUNTER-
CLOCKWISE TO DECREASE
BRAKE TENSION.
INCREASE BRAKE TENSION.
ROTATE NUT COUNTER-
CLOCKWISE TO DECREASE
BRAKE TENSION.
3” to 3-1/4”
CLEARANCE
MEASURE FROM
THIS EDGE
THIS EDGE
BLADE
LEVER
DISENGAGED
LEVER
DISENGAGED