EchoStar dsb-808 2ci Manuale Utente
User Manual
Section 2
EchoNAV Version 2.2
Page 2 - 5
© 2
003 E
c
hoS
tar
Inte
rnati
o
nal
C
o
rp
orat
io
n
A
ll ri
g
h
ts
re
s
e
rv
ed
English
2
2.2.
INSTALLATION SETUP
-
System setup
■
System
Shows the selected installation type you use as defined during
the initial installation. The System can only be changed during
the initial installation which becomes active after a Factory
reset.
the initial installation. The System can only be changed during
the initial installation which becomes active after a Factory
reset.
■
Installation
To select the Easy or Advanced installation mode. Select
Advanced if you want to configure any LNB that is not listed in
the Easy mode. It also lets you configure complex systems with
more than 4 LNBs.
Advanced if you want to configure any LNB that is not listed in
the Easy mode. It also lets you configure complex systems with
more than 4 LNBs.
■
LNBs
To set the number of LNBs you have installed. If you select
more than one LNB, note that the Switch is automatically set.
more than one LNB, note that the Switch is automatically set.
■
Polarity
To set the device that controls the Polarity (not used).
■
Switch
To set the switch that controls the installation. If you have a
system with one LNB, select None. If you select a Switch, note
that LNB1 is automatically allocated to Port1.
system with one LNB, select None. If you select a Switch, note
that LNB1 is automatically allocated to Port1.
■
LNB1, 2, 3, 4
To select the LNB type(s) you use. If your LNB is not listed, go to
Installation and select Advanced.
If your SAT is not listed, select S00 which brings you to the Add
data menu.
For Fixed, select one of the pre-defined LNBs and the SAT. If
you use a Switch the allocated Port shows for each LNB.
For DiSEqC1.2, select one of the pre-defined LNBs.
Installation and select Advanced.
If your SAT is not listed, select S00 which brings you to the Add
data menu.
For Fixed, select one of the pre-defined LNBs and the SAT. If
you use a Switch the allocated Port shows for each LNB.
For DiSEqC1.2, select one of the pre-defined LNBs.
■
Check signal
Check signal verifies the settings you made before. If the
settings are correct, the TP indicator becomes green. If the
indicator becomes red, select another TP or make sure you
have selected the correct Port for this SAT.
If your TP is not listed, select TP00 which brings you to the Add
data menu.
The signal indicator helps you to check the signal quality (top)
and strength (bottom) for the defined SAT and Network.
Search channels will bring you to the next menu to start the
channel search.
settings are correct, the TP indicator becomes green. If the
indicator becomes red, select another TP or make sure you
have selected the correct Port for this SAT.
If your TP is not listed, select TP00 which brings you to the Add
data menu.
The signal indicator helps you to check the signal quality (top)
and strength (bottom) for the defined SAT and Network.
Search channels will bring you to the next menu to start the
channel search.
■
Program satellites
(DiSEqC1.2 only)
(DiSEqC1.2 only)
Program satellites will bring you to the next menu to select the
SAT and define its position.
SAT and define its position.
■
Symbol rate1
(SMATV only)
(SMATV only)
There are four possibilities to enter a Symbol rate that you want
to receive. A green bullet behind the selection includes the
Symbol rate for a channel search.
Search channels will bring you to the next menu to start the
channel search.
to receive. A green bullet behind the selection includes the
Symbol rate for a channel search.
Search channels will bring you to the next menu to start the
channel search.
■
Search channels
Search channels does a channel search on the defined SAT.