EchoStar dsb-808 2ci Manuale Utente
User Manual
Section 2
EchoNAV Version 2.2
Page 2 - 7
© 2
003 E
c
hoS
tar
Inte
rnati
o
nal
C
o
rp
orat
io
n
A
ll ri
g
h
ts
re
s
e
rv
ed
English
2
-
Software upgrade
-
Factory reset
-
Program satellites (Advanced only)
■
OTA settings
Factory1 takes a Software upgrade from Hotbird.
Factory2 takes a Software upgrade from Astra1.
User takes a Software upgrade from a user defined SAT
The signal indicator helps you to check the signal quality (top)
and strength (bottom) for the defined SAT.
Factory2 takes a Software upgrade from Astra1.
User takes a Software upgrade from a user defined SAT
The signal indicator helps you to check the signal quality (top)
and strength (bottom) for the defined SAT.
■
SAT
To select the user defined SAT to take a Software upgrade from.
■
Frequency
For user defined SAT: to select a user defined Frequency.
■
Polarity
For user defined SAT: to select a user defined Polarity.
■
Symbol rate
For user defined SAT: to select a user defined Symbol rate.
■
FEC
For user defined SAT: to select a user defined FEC.
■
Start
Starts the Software upgrade. When the TV screen turns black,
the receiver first compares the current EchoNAV version with
the version on the satellite.
If the EchoNAV version is the same, nothing happens.
If a new EchoNAV version is found on the satellite, the receiver
starts to download the new EchoNAV version in temporary
memory. When the download is complete, the new EchoNAV
version is written to the receiver memory where it deletes the
previous version. This process can take up to approximately
30 minutes.
The Software upgrade is completed when the TV shows live
video.
the receiver first compares the current EchoNAV version with
the version on the satellite.
If the EchoNAV version is the same, nothing happens.
If a new EchoNAV version is found on the satellite, the receiver
starts to download the new EchoNAV version in temporary
memory. When the download is complete, the new EchoNAV
version is written to the receiver memory where it deletes the
previous version. This process can take up to approximately
30 minutes.
The Software upgrade is completed when the TV shows live
video.
■
Memory
-
■
User settings
It is advised to write down the most important settings before
you Confirm the Factory reset (e.g. Switch and Port settings,
LNBs, User preferences, etc.).
If you select Yes, the receiver is ready to do a Factory reset.
you Confirm the Factory reset (e.g. Switch and Port settings,
LNBs, User preferences, etc.).
If you select Yes, the receiver is ready to do a Factory reset.
■
Confirm
If you select Confirm, the receiver deletes all user defined
settings, channels, timers and (favorite) lists and replace them
with the factory defaults. If a Factory reset is done after a
Software upgrade, the latest satellite and transponder database
is activated.
When the Factory reset is completed, the receiver shows the
initial installation procedure as if the receiver came out of the
box.
settings, channels, timers and (favorite) lists and replace them
with the factory defaults. If a Factory reset is done after a
Software upgrade, the latest satellite and transponder database
is activated.
When the Factory reset is completed, the receiver shows the
initial installation procedure as if the receiver came out of the
box.
■
SAT
To define the satellite you want to search channels on.
If your SAT is not listed, select S00 which brings you to the Add
data menu.
If your SAT is not listed, select S00 which brings you to the Add
data menu.
■
Longitude
Shows the orbital position of the defined SAT.
■
User LNB
Shows the LNB that you have selected in the System setup.
With the i-key you can access the User LNB setting menu.
With the i-key you can access the User LNB setting menu.
■
TP
Shows a transponder, from the internal database, of the defined
SAT. If the signal indicator shows low levels, select another TP
that gives a better signal. If your TP is not listed, select TP00
which brings you to the Add data menu.
SAT. If the signal indicator shows low levels, select another TP
that gives a better signal. If your TP is not listed, select TP00
which brings you to the Add data menu.
■
Skew
(not used).
■
Position
To move the dish and find the defined SAT.