Fedders aep09d2a Guida Al Funzionamento
7
Operation
Operating Instructions
Air Conditioner /Cool Mode
1. Install the widow adapter kit and hoses to the unit.
2. Press the On/Off button to turn the unit on. The unit will
2. Press the On/Off button to turn the unit on. The unit will
power up and display the room temperature.
3. Press the Mode button until the green indicator light
shines.
4. Press the Temp/Timer Set buttons to set the desired
temperature. While you are adjusting the setting, the Set
Temperature indicator will shine and the display will show
the set temperature. After you have finished adjusting the
temperature, the display will default back to the room
temperature and the “Room Temp” indicator will shine.
Temperature indicator will shine and the display will show
the set temperature. After you have finished adjusting the
temperature, the display will default back to the room
temperature and the “Room Temp” indicator will shine.
5. Press the Fan Speed button to select the desired setting
(High, Med, Low). The fan speed indicator light will shine
for the selected speed.
for the selected speed.
6. Condensed water may accumulate in the unit. If the
internal tank becomes full, the warning light will shine and
the unit will not operate until the unit has been drained.
See Draining Excess Water section for instructions on how
to drain the water.
the unit will not operate until the unit has been drained.
See Draining Excess Water section for instructions on how
to drain the water.
7. Once the room reaches the set temperature, the
compressor will turn off and the fan will continue to
operate.
operate.
Heat Mode
1. Press the On/Off button to turn the unit on. The unit will
power up and display the room temperature.
2. Press the Mode button until the red indicator light shines.
3. Press the Temp/Timer Set buttons to set the desired
3. Press the Temp/Timer Set buttons to set the desired
temperature. While you are adjusting the setting, the Set
Temperature indicator will shine and the display will show
the set temperature. After you have finished adjusting the
temperature, the display will default back to the room
temperature and the “Room Temp” indicator will shine.
When the room temperature falls below 1° of the set
temperature, the unit will start heating the room. Whe the
room temperature reaches 1° above the set temperature
the unit will stop heating the room. 4. Air flow is adjusted
using the Fan Speed Control. Press the Fan Speed button to
select the desired setting (High, Med, Low). The fan speed
indicator light will shine for the selected speed.
Temperature indicator will shine and the display will show
the set temperature. After you have finished adjusting the
temperature, the display will default back to the room
temperature and the “Room Temp” indicator will shine.
When the room temperature falls below 1° of the set
temperature, the unit will start heating the room. Whe the
room temperature reaches 1° above the set temperature
the unit will stop heating the room. 4. Air flow is adjusted
using the Fan Speed Control. Press the Fan Speed button to
select the desired setting (High, Med, Low). The fan speed
indicator light will shine for the selected speed.
5. Heater Safety feature: After the unit has stopped heating
the room, the fan will continue to run for 5 seconds to
remove any residual heat from the unit. If power is
interrupted during heating mode, the fan will continue to
run for 5 seconds.
remove any residual heat from the unit. If power is
interrupted during heating mode, the fan will continue to
run for 5 seconds.
Dehumidify Mode
1. Press the On/Off button to turn the unit on. The unit will
power up and display the room temperature.
2. Press the Mode button until the orange indicator light
shines above the word Dehumidify.
3. Condensed water may accumulate in the unit. If the
internal tank becomes full, the warning light will shine
and the unit will not operate until the unit has been
drained. See Draining Excess Water section.
and the unit will not operate until the unit has been
drained. See Draining Excess Water section.
4. The fan will operate in Med speed. Fan speed is not
adjustable in Dehumidify mode.
Fan Mode
1. Press the On/Off button to turn the unit on. The unit will
power up and display the room temperature.
2. Press the Mode button until the yellow indicator light
shines.
3. Press the Fan Speed button to select the desired setting
(High, Med, Low). The fan speed indicator light will shine
for the selected speed.
for the selected speed.
4. The unit will operate continuously in Fan mode.
Timer
The timer can be set to turn the unit off or on. The timer is
adjustable between 1 and 12 hours.
The timer can be set to turn the unit off or on. The timer is
adjustable between 1 and 12 hours.
To turn unit off automatically:
1. With unit running in desired mode, press timer button.
2. Use Temp/Timer Set buttons to select number of hours
you would like the unit to run until it automatically
shuts off. After you have finished adjusting the timer,
the display will default back to the room temperature
and the “Room Temp” indicator will shine. Timer
indicator will blink when set. To turn timer off press the
timer button.
shuts off. After you have finished adjusting the timer,
the display will default back to the room temperature
and the “Room Temp” indicator will shine. Timer
indicator will blink when set. To turn timer off press the
timer button.
To turn unit on automatically:
1. With unit powered on select desired mode and fan
speed, then power unit off.
2. With machine powered off, press timer button to select
number of hours until you would like the unit to
automatically start running in air conditioning mode.
Timer indicator will blink when set. The display will
show the number of hours the unit is set until it begins
operation. To turn timer off press the timer button.
automatically start running in air conditioning mode.
Timer indicator will blink when set. The display will
show the number of hours the unit is set until it begins
operation. To turn timer off press the timer button.
Before starting this unit
1. Select a suitable location, making sure you have a level surface with no obstructions, and easy access to an electrical outlet.
2. Install the window adapter kit, as described in the Installation section.
2. Install the window adapter kit, as described in the Installation section.
Note: The window adapter kit is required only while using the Cool mode.
3. Plug the unit into a grounded electrical outlet. Do not use an extension cord.
CAUTION
Heat/Cool models or units with electric heat are designed
to be used only as a supplemental heat source. They
should be used in addition to regular heating systems
and never as the primary source of heat.
to be used only as a supplemental heat source. They
should be used in addition to regular heating systems
and never as the primary source of heat.