Fedders b6y12f2a Guida Al Funzionamento
6
OPERATION
ELECTRONIC CONTROLS
Electronic Control Panel
Power Control
The Power Control turns the unit on and off.
Set Temperature/ Timer Display
Shows the set temperature when the unit is in operation and hours when the timer is
being set. THE TEMPERATURE DISPLAY ONLY SHOWS THE SET TEMPERATURE,
NOT THE ACTUAL ROOM TEMPERATURE.
being set. THE TEMPERATURE DISPLAY ONLY SHOWS THE SET TEMPERATURE,
NOT THE ACTUAL ROOM TEMPERATURE.
Temperature/ Timer Hour Controls
These buttons are used to raise or lower the set temperature in increments of 1° from
66°F to 88°F. By depressing both buttons at once, the display will toggle between
Celsius and Fahrenheit. When the timer is being set, these buttons are used to change
the hour setting in increments of 1 from 00 to 24.
66°F to 88°F. By depressing both buttons at once, the display will toggle between
Celsius and Fahrenheit. When the timer is being set, these buttons are used to change
the hour setting in increments of 1 from 00 to 24.
Mode Control
A green light will indicate which mode is currently being utilized.
Cool Mode –
The unit will circulate and cool the air.
Heat Mode
The unit will circulate and cool the air.
Heat Mode
(Heat Models Only) –
The unit will circulate and heat the air.
Heater Safety Feature- When heater is powered off, low fan will automatically stay on and run
for 60 seconds to ensure the removal of residual heat, meanwhile, the Low Fan LED blinks
until the low fan stops.
Fan Mode –
The unit will only circulate the air.
Energy Saver Mode –
(The energy saver mode is designed to operate with Cool mode only). The fan will
switch from the set fan speed to Low whenever the compressor turns off in response to
the thermostat. When the compressor cycles back on, the unit will return to the
original fan setting. Speeds will change automatically as the temperature in the room
changes.
Heater Safety Feature- When heater is powered off, low fan will automatically stay on and run
for 60 seconds to ensure the removal of residual heat, meanwhile, the Low Fan LED blinks
until the low fan stops.
Fan Mode –
The unit will only circulate the air.
Energy Saver Mode –
(The energy saver mode is designed to operate with Cool mode only). The fan will
switch from the set fan speed to Low whenever the compressor turns off in response to
the thermostat. When the compressor cycles back on, the unit will return to the
original fan setting. Speeds will change automatically as the temperature in the room
changes.
A
B
C
D
E
F
Electronic Control (Cooling Only)
The heat from this unit is designed
only as a supplemental heat
source in addition to
regular heating systems.
only as a supplemental heat
source in addition to
regular heating systems.
Fan Speed Control
-
High, Medium, Low and Auto
The settings are adjusted with the Fan Speed Control, each time the button is
depressed it changes the setting. A green light will indicate which setting is currently
being used.
depressed it changes the setting. A green light will indicate which setting is currently
being used.
When the Auto feature is selected while the air conditioner is in the Cool or Heat
mode, the fan speeds will change automatically as the temperature in the room
changes. In Cool Mode when the room reaches 7° or more above the set temperature
High Fan will be used, 4° or less above the set temperature will use Low fan. In Heat
Mode when the room reaches 7° or more below the set temperature High fan will be
used, 4° or less below the set temperature will use Low fan. At all other times the fan
will use Medium fan.
mode, the fan speeds will change automatically as the temperature in the room
changes. In Cool Mode when the room reaches 7° or more above the set temperature
High Fan will be used, 4° or less above the set temperature will use Low fan. In Heat
Mode when the room reaches 7° or more below the set temperature High fan will be
used, 4° or less below the set temperature will use Low fan. At all other times the fan
will use Medium fan.
To automatically START the unit using the Timer mode:
1. Push the timer button while the power is OFF. The display will read 00. Adjust
the display to show the desired number of hours before START-UP using the
Temperature/Timer adjustment arrows.
Temperature/Timer adjustment arrows.
2. The display will show the amount of time, in hours, remaining until START-UP.
3. To exit Timer mode, push the Timer button.
4. A green light next to the Timer button indicates that the timer is set.
3. To exit Timer mode, push the Timer button.
4. A green light next to the Timer button indicates that the timer is set.
To automatically SHUT-DOWN the unit using the Timer mode:
1. Push the timer button while the power is ON. The display will read 00. Adjust
the display to show the desired number of hours before SHUT-DOWN using the
Temperature/Timer adjustment arrows. (The display will automatically return to the set
temperature after 10 seconds.)
Temperature/Timer adjustment arrows. (The display will automatically return to the set
temperature after 10 seconds.)
2. To display the amount of time left until SHUT-DOWN, push the Timer button
once.
3. To exit Timer mode, push the Timer button twice.
4. A green light next to the Timer button indicates that the timer is set.
4. A green light next to the Timer button indicates that the timer is set.
Timer Control
(
The timer can be set to either turn the unit on or off.)
Built in Three Minute Cooling Delay
Cool
High
Timer
Med
Auto
Low
Fan
Energy Save
Heat
On/Off
A
B
C
C
D
D
E
E
F
F
Temperature/Timer Display
Temperature/Timer Adjustment
Timer On/Off
Fan Speed Control
Mode Control
Power Control
A
B
Electronic Control (Heat/Cool)