Calflame cr2000 Manuale Utente
Page 12
2007 Barbecue Grill and Cart Owner’s Manual
LTR20071038, Rev. B
Installation / Assembly
Installing Grills in Modular Carts
You will need a second person to help you to
avoid damaging the grill, the transformer, or your
barbecue island .
avoid damaging the grill, the transformer, or your
barbecue island .
Keep fingers away from where the grill will be
supported on the cart. Your fingers could become
trapped and serious injury could occur .
trapped and serious injury could occur .
Slowly lower grill unit onto the cart, making sure
that screws line up with slots on top of the cart.
Ensure that no electrical cords or gas lines become
trapped between any part of the cart and any part
of the grill.
that screws line up with slots on top of the cart.
Ensure that no electrical cords or gas lines become
trapped between any part of the cart and any part
of the grill.
The grill should sit flat on the cart all the way
around. Gently realign cart sides to allow them to
sit under outside lip of grill.
around. Gently realign cart sides to allow them to
sit under outside lip of grill.
Check that all burner control knobs are in the OFF
position.
position.
Attach the gas connector to the LP tank.
When handling the LP gas line and connectors, do not
allow them to come in contact with any metal surfaces
of the cart or cabinet. Do not drop LP connectors.
allow them to come in contact with any metal surfaces
of the cart or cabinet. Do not drop LP connectors.
1.
2.
3.
4.
Installing Grills in Barbecue
Islands
Islands
You will need a second person to help you to
avoid damaging the grill, the transformer, or your
barbecue island .
avoid damaging the grill, the transformer, or your
barbecue island .
Before installing a grill or side burner in any island or
cut out, make sure that the opening is not bigger than
the outside frame of the grill unit. The grill should
rest on the lip of the frame. For drop-in accessories,
cut out, make sure that the opening is not bigger than
the outside frame of the grill unit. The grill should
rest on the lip of the frame. For drop-in accessories,
adequate cross ventilation must be designed into
enclosure to ensure the drop-in grill or side burner does
not become overheated.
enclosure to ensure the drop-in grill or side burner does
not become overheated.
Pay careful attention to the location of gas lines. Gas
lines should be routed away from sources of heat and
should make as few bends as possible.
lines should be routed away from sources of heat and
should make as few bends as possible.
Check to see if gas line connections will be accessible
when grill is installed.
when grill is installed.
If gas line connections are not easily accessible
when the grill is installed, support the grill above
counter level and attach the gas lines to the grill.
When the gas connections are made, slide the grill
into the cut out.
when the grill is installed, support the grill above
counter level and attach the gas lines to the grill.
When the gas connections are made, slide the grill
into the cut out.
If gas line connections are accessible when the grill
is installed, slide the grill into the cut out and then
attach the gas lines.
is installed, slide the grill into the cut out and then
attach the gas lines.
Be very careful not to kink gas lines when lowering the
grill or side burner into the cut out.
grill or side burner into the cut out.
Keep your fingers away from where the grill will be
supported on counter. Your fingers could become
trapped and serious injury could occur.
Check to make sure the grill is level and is supported
around the entire outside edge. If the grill is not level
or is unstable, use non-combustible shims under the
outside lip to stabilize it.
around the entire outside edge. If the grill is not level
or is unstable, use non-combustible shims under the
outside lip to stabilize it.
Perform the leak test procedure as described earlier in
this manual.
this manual.
•
•