Cisco Cisco TelePresence MX700 Guida All'Installazione
D14639.06 Video Systems Getting Started Guide (TC5.1) | 2012 FEBRUARY | © 2011-2012 Cisco Systems, Inc. All rights reserved.
www.cisco.com
21
GettinG started Guide
remote control and on-screen menu
Configuring H.323 and SIP
(when not set by a provisioning system)
To get online and ready to place and receive calls, your
system must be set up properly. Your system uses either
the H.323 protocol or the SIP protocol for video calls.
NoTE:
Contact your system administrator, or service
provider, for information about the network settings.
For networks administered through Cisco TMS (Cisco
TelePresence Management Suite) your Cisco TMS
administrator will help you to get online.
H.323
If in doubt for any of the parameters below, contact your
system administrator or your service provider.
1. Go to
Home > Settings > Administrator settings >
Advanced configuration > H323 > Profile 1
.
2. Go to
H323Alias
and enter the
E164
number
and
ID
in
the corresponding input fields.
3. If you want the system to obtain the H.323 gatekeeper
address automatically, go to
Gatekeeper
and select
Auto
in the
Discovery
drop down list; if you want to enter the
address manually, select
Manual.
If set to
Manual
enter the gatekeeper address in the
Address
input field.
4. If the H.323 gatekeeper requires authentication and
you want your system to authenticate itself to the
gatekeeper, go to
Authentication
and select
On
in the
Mode
drop down list; otherwise select
Off.
If set to
On
enter the
LoginName
and
Password
in the
corresponding input fields.
5. Go to
Home > Settings > System information
and verify
the H323 settings.
If you successfully registered to the Gatekeeper the
If you successfully registered to the Gatekeeper the
Status
is shown as
Registered
in the H323 section.
6. Press
Home
( )
to exit.
Please check the Administrator guide for your product if you
want to change the other H.323 settings.
SIP
If in doubt for any of the parameters below, contact your
system administrator or your service provider.
1. Go to
Home > Settings > Administrator settings >
Advanced configuration > SIP > Profile 1
.
2. Go to
URI
and enter the SIP URI in the corresponding
input field.
3. Select your preferred
Default Transport
protocol in the
drop down list. If you select
Auto
the system first tries to
connect using TLS, then TCP, and finally UDP.
4. Select your preferred proxy
Type
in the drop down list.
The default type is
Standard
.
5. Go to
Proxy 1.
If you want the system to obtain the SIP
proxy address automatically, select
Auto
in the
Discovery
drop down list; if you want to enter the address manually,
select
Manual
.
If set to
Manual
enter the proxy address in the
Address
input field.
6. If the SIP proxy requires authentication you must enter a
login name and password to authenticate your system.
Go to
Authentication 1
and enter the
LoginName
and
Password
in the corresponding input fields.
7. Go to
Home > Settings > System information
and verify
the SIP settings.
If you successfully registered to a SIP server the
If you successfully registered to a SIP server the
Status
is shown as
Registered
in the SIP section.
8. Press
Home
( )
to exit.
Please check the Administrator guide for your product if you
want to change the other SIP settings.
Save the new value when you change a setting
• Drop down list selection: Navigate to the correct
value and press the
OK
( )
key to save, or press
the left arrow key to leave without saving.
• Text entry in an input field: Enter the text, navigate
to
Ok/Save
to save the change, or navigate to
Cancel
to leave without saving; then press the
OK
( ) key
to confirm.
Back to task overview
User interfaces
Introduction
Configuration
Table of contents
Appendices
Configuration