HP color laserjet 9500mfp Manuale Utente
Output Protocol
This control specifies the protocol that the product uses for print jobs. The following options are
available:
available:
■
ASCII (default)
■
TBCP
■
Binary
When you click ASCII, data is sent in ASCII format (7-bit), which might take longer to print but can be
sent through any I/O channel, such as a serial, parallel, or network port.
sent through any I/O channel, such as a serial, parallel, or network port.
When you click TBCP (Tagged Binary Communications Protocol), all data except special control
characters is sent in binary (8-bit) format. The binary formats can be sent over parallel or serial
communications ports and are faster than sending data in ASCII format.
characters is sent in binary (8-bit) format. The binary formats can be sent over parallel or serial
communications ports and are faster than sending data in ASCII format.
When you click Binary, all data except special control characters is sent in binary (8-bit) format. The
binary formats can be sent over parallel or serial communications ports and are faster than sending
data in ASCII format.
binary formats can be sent over parallel or serial communications ports and are faster than sending
data in ASCII format.
Send Ctrl-D Before Each Job
This control specifies whether the product will be reset at the beginning of every postscript
document. The default setting is No. Ctrl-D resets the product to its default setting to ensure that
previous print jobs do not affect the current print job. Ctrl-D might cause a print job to fail if the
product is connected through a network. If your document fails to print when sent to a product
connected through parallel or serial ports, change No to Yes.
document. The default setting is No. Ctrl-D resets the product to its default setting to ensure that
previous print jobs do not affect the current print job. Ctrl-D might cause a print job to fail if the
product is connected through a network. If your document fails to print when sent to a product
connected through parallel or serial ports, change No to Yes.
Send Ctrl-D After Each Job
This control specifies whether the product will be reset at the end of every postscript document. The
default setting is Yes. Ctrl-D resets the product to its default setting to ensure that future print jobs
are not affected by the current print job. Ctrl-D might cause a print job to fail if the product is
connected through a network. If your document fails to print when sent to a network printer, change
Yes to No.
default setting is Yes. Ctrl-D resets the product to its default setting to ensure that future print jobs
are not affected by the current print job. Ctrl-D might cause a print job to fail if the product is
connected through a network. If your document fails to print when sent to a network printer, change
Yes to No.
Job Timeout
This control specifies how long the document can take to get from the computer to the product before
the product stops trying to print the document. If you specify 0 seconds, the product continues trying
to print indefinitely. The default setting is 0 seconds. You can use the spin box to change this value
to a maximum of 32,767 seconds.
the product stops trying to print the document. If you specify 0 seconds, the product continues trying
to print indefinitely. The default setting is 0 seconds. You can use the spin box to change this value
to a maximum of 32,767 seconds.
Wait Timeout
This control specifies how long the product waits to get more postscript information from the
computer. After the specified time passes, the product stops trying to print the document and prints
an error message. If you are trying to print a very complicated document, you might want to increase
this value. If you specify 0 seconds, the product waits indefinitely. The default setting is 300
seconds. You can use the spin box to change this value to a maximum of 32,767 seconds.
computer. After the specified time passes, the product stops trying to print the document and prints
an error message. If you are trying to print a very complicated document, you might want to increase
this value. If you specify 0 seconds, the product waits indefinitely. The default setting is 300
seconds. You can use the spin box to change this value to a maximum of 32,767 seconds.
Minimum Font Size to Download as Outline
This control specifies the minimum font size (in pixels) for which the driver downloads TrueType fonts
as outline (Type 1) fonts. A font smaller than the minimum setting is downloaded as a bitmap (Type
3) font. Use this option to fine-tune the Automatic setting for the TrueType Font Download option
as outline (Type 1) fonts. A font smaller than the minimum setting is downloaded as a bitmap (Type
3) font. Use this option to fine-tune the Automatic setting for the TrueType Font Download option
HP PCL 6, HP PCL 5, and HP PS Unidriver features
233