HP mhp-tn Manuale Utente
MHP-TN USER INSTRUCTIONS ENGLISH 71576313 - 02/07
Page 27 of 28
flowserve.com
8.2 Sectional drawings part list
ITEM
DESIGNATION
1110
Pump casing
1221
Casing cover with stuffing box
1500
Wear ring
2110
Pump shaft
2250
Radial flow impeller
2450
Shaft sleeve
2540
Thrower
2905
Plain washer
2912
Self-braked nut
3011
Radial ball bearing
3134
Support foot
3200
Bearing housing
3260
Bearing cover
3300
Bearing bush
4120
Gland
4130
Gland packing
4132
Stuffing box neck bush
4590-01
Gasket
4590-02
Gasket
4590-03
Special ring
6511
Priming plug
6515
Drain plug
6544
Bore circlip
6569
Screwed plug
6572
Stud
6577-01
Hexagon bolt
6577-02
Hexagon bolt
6577-03
Hexagon bolt
6581
Hexagon nut
6700-01
Key
6700-02
Key
9331
Cover plate
8.3 General arrangement drawing
The typical general arrangement drawing and any
specific drawings required by the contract will be sent
to the Purchaser separately unless the contract
specifically calls for these to be included into the User
Instructions. If required, copies of other drawings
sent separately to the Purchaser should be obtained
from the Purchaser and retained with these User
Instructions.
specific drawings required by the contract will be sent
to the Purchaser separately unless the contract
specifically calls for these to be included into the User
Instructions. If required, copies of other drawings
sent separately to the Purchaser should be obtained
from the Purchaser and retained with these User
Instructions.
9 CERTIFICATION
Certificates determined from the Contract
requirements are provided with these instructions
where applicable. Examples are certificates for CE
marking, ATEX marking etc. If required, copies of
other certificates sent separately to the Purchaser
should be obtained from the Purchaser for retention
with these User Instructions.
requirements are provided with these instructions
where applicable. Examples are certificates for CE
marking, ATEX marking etc. If required, copies of
other certificates sent separately to the Purchaser
should be obtained from the Purchaser for retention
with these User Instructions.
10 OTHER RELEVANT
DOCUMENTATION AND MANUALS
DOCUMENTATION AND MANUALS
10.1 Supplementary User Instructions
Supplementary instructions such as for a driver,
instrumentation, controller, seals, sealant system etc
are provided as separate documents in their original
format. If further copies of these are required they
should be obtained from the supplier for retention
with these User Instructions.
instrumentation, controller, seals, sealant system etc
are provided as separate documents in their original
format. If further copies of these are required they
should be obtained from the supplier for retention
with these User Instructions.
10.2 Change notes
If any changes, agreed with Flowserve, are made to the
product after its supply, a record of the details should
be maintained with these User Instructions.
product after its supply, a record of the details should
be maintained with these User Instructions.
10.3 Additional sources of information
Reference 1:
NPSH for Rotor dynamic Pumps: a reference guide,
Euro pump Guide No. 1, Euro pump & World Pumps,
Elsevier Science, United Kingdom, 1999.
NPSH for Rotor dynamic Pumps: a reference guide,
Euro pump Guide No. 1, Euro pump & World Pumps,
Elsevier Science, United Kingdom, 1999.
Reference 2:
Pumping Manual, 9
Pumping Manual, 9
th
edition, T.C. Dickenson,
Elsevier Advanced Technology, United Kingdom, 1995.
Reference 3:
Pump Handbook, 2
Pump Handbook, 2
nd
edition, Igor J. Karassik et al,
McGraw-Hill Inc., New York, 1993.
Reference 4:
ANSI/HI 1.1-1.5, Centrifugal Pumps - Nomenclature,
Definitions, Application and Operation.
ANSI/HI 1.1-1.5, Centrifugal Pumps - Nomenclature,
Definitions, Application and Operation.
Reference 5:
ANSI B31.3 - Process Piping.
ANSI B31.3 - Process Piping.