Yamaha aw16g Manuale Utente
205
Appendix
3.1.9. Program Change Mode
Enable/disable reception and transmission. If MIDI Rx Ch is set to
ALL, these messages will be received regardless of their MIDI chan-
nel.
ALL, these messages will be received regardless of their MIDI chan-
nel.
3.1.10. Control Change Mode
If this is enabled, you can specify the correspondence between con-
trol numbers and operations of the mixer section. For mode 1, trans-
mission and reception will occur without regard to the MIDI Tx Ch
and MIDI Rx Ch settings. For modes 2 and 3, reception will occur
without regard to MIDI channel if you set MIDI Rx Ch to ALL.
trol numbers and operations of the mixer section. For mode 1, trans-
mission and reception will occur without regard to the MIDI Tx Ch
and MIDI Rx Ch settings. For modes 2 and 3, reception will occur
without regard to MIDI channel if you set MIDI Rx Ch to ALL.
3.2. MIDI BULK DUMP
Controls transmission of Bulk Dump and Bulk Dump Request.
3.2.1. BULK DUMP Category
Selects the type of parameters for Dump or Dump Request.
3.2.1.1. SCENE
Mixer scene settings. E.BUF is the current state, 01-96 are stored
scenes. ALL selects all scenes.
scenes. ALL selects all scenes.
3.2.1.2. LIBRARY
All memory settings for all libraries (EQ / EFFECT / DYNAMICS /
CHANNEL).
CHANNEL).
3.2.1.3. SYSTEM
Settings that apply to the entire AW16G.
3.2.1.4. REMOTE
Settings for the MIDI Remote function.
3.2.1.5. PROGRAM CHANGE TABLE
This is the Program Change Table.
3.2.1.6. ALL
All of the above settings.
3.2.2. INTERVAL
Specifies the interval at which consecutive Bulk Dump or Bulk
Dump Request messages will be transmitted. Increase this setting if
the receiving device fails to receive all of the bulk data.
Dump Request messages will be transmitted. Increase this setting if
the receiving device fails to receive all of the bulk data.
3.2.3. RX DISABLE
If RX Disable is turned on, no Bulk Dump or Bulk Dump Request
messages will be received.
messages will be received.
3.2.4. REQUEST
Transmits the selected Bulk Dump Request.
3.2.5. TRANSMIT
Transmits the selected Bulk Dump.
3.3. MIDI PROGRAM CHANGE TABLE
This table allows you to freely specify the correspondence between
Program Change No. and Scene No.
This table is used for conversion for both transmission and recep-
tion.
Program Change No. and Scene No.
This table is used for conversion for both transmission and recep-
tion.
4. MIDI format list
4.1. CHANNEL MESSAGE
4.2. SYSTEM COMMON MESSAGE
4.3. SYSTEM REALTIME MESSAGE
4.4. SYSTEM EXCLUSIVE MESSAGE
4.4.1. REALTIME SYSTEM EXCLUSIVE
4.4.1.1. MMC
4.4.1. REALTIME SYSTEM EXCLUSIVE
4.4.1.1. MMC
4.4.2. BULK DUMP / BULK DUMP REQUEST
Command
Rx/Tx
function
8n
NOTE OFF
Rx
Control the internal effect
9n
NOTE ON
Rx
Control the internal effect
Bn
CONTROL CHANGE
Rx/Tx
Edit parameters
Cn
PROGRAM CHANGE
Rx/Tx
Switch scene memories
Command
Rx/Tx
function
F1
MIDI TIME CODE
Rx/Tx
MTC transmission
F2
SONG POSITION POINTER
Tx
Song position transmission
Command
Rx/Tx
function
F8
TIMING CLOCK
Tx
MIDI Clock transmission
FA
START
Tx
Start command transmission
FB
CONTINUE
Tx
Continue command transmission
FC
STOP
Tx
Stop command transmit
FE
ACTIVE SENSING
Rx
Check MIDI cable connections
FF
RESET
Rx
Clear running status
Command
Rx/Tx
function
01
STOP
Rx/Tx
Transport stop
02
PLAY
Rx
Transport play
03
DEFERRED PLAY
Rx/Tx
Transport play
04
FAST FORWARD
Rx/TX
Transport fast-forward
05
REWIND
Rx/Tx
Transport rewind
06
RECORD STROBE
Rx
Transport punch-in record
07
RECORD EXIT
Rx
Transport punch-out
0F
RESET
Rx/Tx
MMC reset
44
LOCATE
Rx/Tx
Transport locate
Data Name
Rx/Tx
function
'M'
Rx/Tx
Scene Memory & Request
'S'
Rx/Tx
System Memory & Request
'R'
Rx/Tx
Remote Memory & Request
'Q'
Rx/Tx
Equalizer Library & Request
'Y'
Rx/Tx
Dynamics Library & Request
'E'
Rx/Tx
Effect Library & Request
'H'
Rx/Tx
Channel Library & Request
'P'
Rx/Tx
Program Change Table & Request