Yamaha aw16g Manuale Utente

Appendix

206

Received when [Rx CH] matches.
Used to control effects. Refer NOTE ON for details.

Received when [Rx CH] matches.
Used to control effects. Refer below for details.
Velocity of 0x00 is equivalent to Note-Off.

* Effect control by Note
1: Dynamic Flange/Dynamic Phase/Dynamic Filter
When the SOURCE parameter is set to MIDI, the note velocity (both 
note-on and note-off) is used to control the Modulation frequency 
width.

Control change messages will be received if the [Control Change 
Mode] is RX or TX/RX and the [MIDI Rx Ch] matches. However if 
[MIDI Rx Ch] is ALL, this message is received regardless of the chan-
nel.

If [Control Change Mode] is TX or TX/RX, control change messages 
will be transmitted on the [MIDI Tx Ch] channel when you operate a 
parameter.

The control value is converted into a parameter value according to 
the following equation.
S= total number of steps in the parameter’s variable range
128 / S = X remainder Y
INT((Y+1)/2) = Z
If (MIDI DATA - Z) < 0, then Value = 0
If ((MIDI DATA - Z)/X) > MAX, then Value = MAX
Otherwise, Value = INT ((MIDI DATA -Z)/X)

Program change messages will be received if the [Program Change 
Mode] is RX or TX/RX and the [MIDI Rx Ch] matches. However if 
[MIDI Rx Ch] is ALL, this message is received regardless of the chan-
nel.
A scene memory will be recalled according to the [PROGRAM 
CHANGE TABLE] settings.

If [Program Change Mode] is TX or TX/RX, a program change will 
be transmitted on the [MIDI Tx Ch] according to the [PROGRAM 
CHANGE TABLE] settings when you recall a memory number. If the 
recalled memory number has been assigned to more than one pro-
gram number, the lowest-numbered program number will be trans-
mitted.

If [MIDI OUT] is set to MTC, Quarter Frame messages will be trans-
mitted according to the time code movements of the recorder when 
the recorder is playing or recording.

This message is received if [MTC SYNC MODE] is set to SLAVE. 
Quarter Frame messages received in realtime are internally assem-
bled into time code that controls the recorder.

If [MIDI OUT] is set to CLK, a song position message will be trans-
mitted when STOP or LOCATE is performed on the recorder, to 
indicate the song position from which the song should start at the 
next START or CONTINUE message.

If [MIDI CLK] is ON, this message is transmitted according to the 
MIDI Tempo Map from when the recorder begins playing or record-
ing, until it stops.

If [MIDI CLK] is ON, this message is transmitted when the recorder 
begins playing or recording at a location other than the first measure.

If [MIDI CLK] is ON, this message is transmitted when the recorder 
begins playing or recording at a location other than the first measure.

If [MIDI CLK] is ON, this message is transmitted when the recorder 
stops.

Once this message is received, subsequent failure to receive any mes-
sage for a period of 300 ms will cause Running Status to be cleared, 
and MIDI communications to be initialized.

When a Reset message is received, MIDI communications will be ini-
tialized by clearing Running Status etc.

When the STOP key is pressed, this message is transmitted with a 
device number of 7F.

STATUS

1000nnnn 8n

Note Off Message

DATA

0nnnnnnn nn

Note No.

0vvvvvvv vv

Velocity ( ignored)

STATUS

1001nnnn 9n

Note On Message

DATA

0nnnnnnn nn

Note No.

0vvvvvvv vv

Velocity ( 1-127:On, 0:off)

STATUS

1011nnnn Bn

Control Change

DATA

0ccccccc cc

Control No. (0-95, 102-119)

0vvvvvvv vv

Control Value (0-127)

STATUS

1100nnnn Cn

Program Change

DATA

0nnnnnnn nn

Program No. ( 0-127)

STATUS

11110001 F1

Quarter Frame Message

DATA

0nnndddd dd

nnn = message type (0-7)   dddd = data

STATUS

11110010 F2

Song Position Pointer

DATA

0ddddddd dd0

data( H) high 7 bits of 14 bits data

0ddddddd dd1 

data( L) low 7 bits of 14 bits data

STATUS

11111000 F8

Timing Clock

STATUS

11111010 FA

Start

STATUS

11111011 FB

Continue

STATUS

11111100 FC

Stop

STATUS

11111110 FE

Active Sensing

STATUS

11111111 FF

Reset