Yamaha digital mixing studio 01x Manuale Utente

01X   Owner’s Manual

■ Pairing was specified, but the signal phase 

• Even when channels are paired, 

the phase setting is not linked. ................................ page 102

■ Automation (Automix) cannot be stopped.

• Has the REMOTE AUTOMATION SETUP 

parameter been set to correctly? ............................... page 88

■ Can’t use the internal effects.

• Effect BYPASS may be turned ON......................... page 102

• Are the level of STEREO IN 1, 2 faders raised?........ page 99

• EFFECT PATCH may be set to 

insertion (each channel).......................................... page 102

• It is not possible to insert one effect 

into multiple channels. ........................................... page 102

• 019. HQ. Pitch can be used only with EFFECT 1.

• When the sampling rate is 96kHz/88.2kH, only Effect 1 can be 

used.

■ Can’t use SOLO.

• The channel may be set to Solo Safe......................... page 96

■ Fader groups and mute groups don’t work.

• In the Fader Group page and Mute Group page, 

check that grouping is set to ENABLE. .................. page 101

■ The pitch is wrong.

• Is the 01X operating on the same sampling frequency 

as the synchronized external device?

......... page 92, “Connecting a Computer to an mLAN 

device via mLAN” (Installation Guide), “mLAN Con-
nection Settings” (Graphic Patchbay Online Manual)

• Is the master device operating in a stable way?

• Is an effect such as HQ.Pitch or 

Dual Pitch selected? ............................................... page 102

■ The layer of 17-24 (mLAN9-16) cannot be 

• When the sampling rate is set to 96kHz/88.2kHz, 

the layer of 17 – 24 (mLAN) can not be selected. ..... page 40

■ Cannot edit with Studio Manager.

• Has the STUDIO MANAGER ID 

been set correctly?.................................................... page 94

• Is Port 4 (Studio Manager) selected for 

Studio Manager data transmission/reception?

.......................... Studio Manager Owner’s Manual (PDF)

■ The Remote Control or Automation 

• Is the correct DAW software selected in Remote Select?

........ page 87, “Demo playback/Remote Control Setup”  

(Installation Guide)

• Are the mLAN settings correct?

.........“Demo playback/Remote Control Setup” 

(Installation Guide)

• Are settings on the DAW correct?

.........page 87, “Demo playback/Remote Control Setup” 

(Installation Guide)

• Is Port 1 selected for mLAN MIDI transmission/reception?

.........page 87, “Demo playback/Remote Control Setup” 

(Installation Guide)

■ Cannot change the wordclock.

• Set this with the mLAN Auto Connector or 

Graphic Patchbay when using mLAN.

.........“Connecting a Computer to an mLAN device via 

mLAN” (Installation Guide),  “Wordclock Settings” 
(Graphic Patchbay Online Manual)

• Is the mLAN Auto Wordclock (AUTO W.CLK) 

setting appropriate?

.........“Connecting a Computer to an mLAN device via 

mLAN” (Installation Guide)

■ The mLAN connection does not work.

• Has the driver been installed? .................... Installation Guide

• Is the mLAN cable properly connected?  Check the connec-

tion; disconnect the mLAN cable once, then insert it again.

• (For Windows) Is mLAN set to “ON”?  From the taskbar, 

right click on the mLAN Manager icon.

.........“Confirming the installation” (Installation Guide)

• (For Windows) When adding a new IEEE 1394 card, right click 

on the mLAN Manager icon in the taskbar and select “ON.”.

.........“Confirming the installation” (Installation Guide)

• Is the ACTIVE lamp on the rear panel of the 01X lit (in blue)?  

If it is not lit, check the followings:

• In mLAN Driver Setup (from taskbar, right click on the mLAN 

Manager icon, then “Driver Setup”), is the Status indicator 
blue?  If not, restart the 01X and re-enable connection by using 
mLAN Auto Connector or Graphic Patchbay.

.........“Confirming the installation” (Installation Guide), 

Graphic Patchbay Online Manual

• Is mLAN AUTO W.CLK (Auto Wordclock) 

on the 01X set to “ENABLE”?

.........“Connecting a Computer to an mLAN device via 

mLAN” (Installation Guide)

• Has connection been enabled with mLAN 

Auto Connector or Graphic Patchbay?  
Re-enable connection if necessary.

.........“Connecting the Computer and mLAN devices via 

mLAN” (Installation Guide), “mLAN Connection 
Settings” (Graphic Patchbay Online Manual)

• Have you changed the device?  Even if the model is the same, 

if the actual device is different, it is necessary to re-enable con-
nection by using mLAN Auto Connector or Graphic Patchbay.

.........“Connecting the Computer and mLAN devices via 

mLAN” (Installation Guide), “mLAN Connection 
Settings” (Graphic Patchbay Online Manual)

• Is there a loop connection?  Check the cabling and make sure 

none of the devices are connected in a loop.