Yamaha YSP-4300 Manuale Utente
Initial settings
31
En
PR
EPARA
TION
PL
AYBACK
AYBACK
SET
TINGS
TRO
UBLE
SHO
OTI
NG
A
PPEN
DIX
When the connected components and jacks are changed, reset this
unit with the following procedure.
unit with the following procedure.
Setting the HDMI control function
1
Turn on all components connected to this
unit via HDMI cable.
unit via HDMI cable.
2
Enable the HDMI control function of all
components connected to this unit via
HDMI cable.
components connected to this unit via
HDMI cable.
For this unit, set “HDMI CONTROL” to “ON” (
2)
For external components, refer to the manual supplied
with each component.
with each component.
3)
3
Turn off the TV and then turn on it again.
Registering HDMI compatible
components to the TV
components to the TV
4)
1
Select this unit as the input source of the
TV.
TV.
2
Turn on an external components, such as
a Blu-ray disc player, connected to this
unit via HDMI cable.
a Blu-ray disc player, connected to this
unit via HDMI cable.
3
Select the input source of this unit to
Blu-ray disc player and check whether the
image in the player is correctly displayed
or not.
Blu-ray disc player and check whether the
image in the player is correctly displayed
or not.
If the Blu-ray disc player is connected via HDMI IN1
jack, press the HDMI1 key.
jack, press the HDMI1 key.
4
Check if the HDMI control function works
(turn on this unit or adjust the volume level
using the remote control of the TV).
(turn on this unit or adjust the volume level
using the remote control of the TV).
HDMI1
Input source name
If the HDMI control function is not working
Be sure that all components are correctly connected to this
unit, and that settings are properly configured as described
below.
– The TV is connected to the HDMI OUT (ARC) jack of this
unit, and that settings are properly configured as described
below.
– The TV is connected to the HDMI OUT (ARC) jack of this
unit.
– “HDMI CONTROL” (
☞p. 63) is set to “ON” in the setup
menu.
– The HDMI control function is enabled on the TV. (Also
check the relative settings such as power interlock function
or speaker priority.)
or speaker priority.)
When the HDMI control function is not still working even
after the above has been checked,
– Turn off this unit and the TV, and then turn them back on
after the above has been checked,
– Turn off this unit and the TV, and then turn them back on
again.
– Disconnect the AC power supply cable of the unit and
external components connected to the unit via HDMI cable.
Plug them in again after about 30 seconds.
Plug them in again after about 30 seconds.
– After OPTICAL, ANALOG, AUX, YIT, or USB
5)
input
has been enabled, switch the input source for the TV and
this unit to the components connected via HDMI cable.
this unit to the components connected via HDMI cable.
Changing the connection method and
connected components
connected components
1
Disable the HDMI control function of the
TV and Blu-ray disc player, turn off all
connected components, and change the
connections.
TV and Blu-ray disc player, turn off all
connected components, and change the
connections.
2
Perform steps 1 to 3 of “Setting the HDMI
control function”.
control function”.
• The default setting is “OFF”.
• When “HDMI CONTROL” is set to “ON”
• When “HDMI CONTROL” is set to “ON”
When the Eco function (
☞p. 41) is enabled, this unit enters standby
mode if the TV is selected for audio output using the TV’s remote
control.
control.
The example of TV settings
• From the setup menu on your TV, select “Link setting” “HDMI
• From the setup menu on your TV, select “Link setting” “HDMI
control setting”, then set a setting such as “HDMI control function” to
“ON”.
“ON”.
• Setting such as “Speaker priority” should be set to “AV amplifier”.
For some HDMI compatible components, registering HDMI compatible
components to TV is not required in this case when the HDMI control
function is enabled.
components to TV is not required in this case when the HDMI control
function is enabled.
YSP-4300 only
2)
y
3)
y
4)
y
5)
y