Ariens 924121 1128 Manuale Utente

GB - 18

IMPORTANT: Allow unit and engine to adjust 
to the outdoor temperatures before clearing 
snow. Before shut-off, run the attachment a 
few minutes to prevent freeze-up.
NOTE: Try out each control without the engine 
running to see how it works and what it does.

1. Turn discharge chute straight ahead.
2. Make sure that the traction clutch and 

attachment drive clutch levers are fully 
disengaged.

3. Push Primer Bulb 2 or 3 times for cold 

engine.

NOTE: When temperature is below -15˚ F 
(-26˚ C) additional priming may be needed.

4. If engine is cold, apply choke. See Engine 

Manual for detailed instructions.

NOTE: A warm engine requires less choking 
than a cold engine. 

5. Set throttle to proper starting position.
6. Insert key into ignition switch.

12V - Turn key into RUN position.
120V - Push key into RUN position. DO 
NOT twist key after it is inserted.

7. Grasp starter handle and pull rope out 

slowly until it pulls harder. Let rope rewind 
slowly.

8. Pull rope with a rapid continuous full arm 

stroke. Let rope rewind slowly. 

IMPORTANT: DO NOT let Starter Handle 
snap against Starter. 

9. Repeat steps 7 and 8 until engine starts. 

(If engine does not start, refer to 
Troubleshooting.)

10. Adjust choke as needed.
11. Set throttle to Part Throttle or Slow 

position for adaptation to outside 
temperature or travel. Set throttle to Fast 
position for normal operation.

1. Connect extension cord to prongs on 

starter.

IMPORTANT: Prevent damage to unit. Know 
voltage of your starter and only use matching 
outlets.

2. Plug extension into 120V 3-wire, 

grounded outlet.

3. Turn discharge chute straight ahead.
4. Make sure that the traction clutch and 

attachment drive clutch levers are fully 
disengaged.

5. Push Primer Bulb 2 or 3 times for cold 

engine.

NOTE: When temperature is below -15˚ F 
(-26˚ C) additional priming may be needed.

6. Insert key into ignition switch on engine 

and push into "Run" position. DO NOT 
twist key after it is inserted.

7. If engine is cold, apply choke. A warm 

engine requires less choking than a cold 
engine. See Engine Manual for detailed 
instructions. 

8. Set throttle to proper starting position.
9. Press starter button on engine until 

engine starts.

IMPORTANT: DO NOT operate starter more 
than 15 seconds per minute, as overheating 
and damage can occur. (If engine does not 
start, refer to Troubleshooting.)

10. Adjust choke as needed.
11. Disconnect power cord from outlet, then 

starter.

12. Set throttle to Part Throttle or Slow 

position for travel or adaptation to outside 
temperature. Once achieved, set throttle 
to Fast position for normal operation.

1. Turn discharge chute straight ahead.
2. Make sure that the traction clutch and 

attachment drive clutch levers are fully 
disengaged.

3. Push Primer Bulb 2 or 3 times for cold 

engine.

NOTE: When temperature is below -15˚ F 
(-26˚ C) additional priming may be needed.

4. If engine is cold, apply choke. See Engine 

Manual for detailed instructions.

NOTE: A warm engine requires less choking 
than a cold engine.

5. Set throttle to proper starting position.
6. Put ignition key into START position until 

engine starts and release into the RUN 
position.

WARNING: FAILURE TO FOLLOW 
INSTRUCTIONS could result in 
personal injury and/or damage to 
unit. DO NOT attempt to start your 
unit at this time. Read entire 
Owner/Operator Manual and the 
Engine Manual first.