Ariens 924121 1128 Manuale Utente
GB - 19
IMPORTANT: DO NOT operate starter more
than 15 seconds per minute, as overheating
and damage can occur. (If engine does not
start, refer to Troubleshooting.)
than 15 seconds per minute, as overheating
and damage can occur. (If engine does not
start, refer to Troubleshooting.)
7. Adjust choke as needed.
8. Set throttle to Part Throttle or Slow
8. Set throttle to Part Throttle or Slow
position for travel or adaptation to outside
temperature. Once achieved, set throttle
to Fast position for normal operation.
temperature. Once achieved, set throttle
to Fast position for normal operation.
Shut Off
1. Release Traction Drive Clutch Lever and
allow unit to come to a complete stop.
2. Run Impeller a few minutes after use to
prevent freeze-up of Impeller.
3. Release Attachment Clutch Lever and
wait for all moving parts to come to a
complete stop.
complete stop.
4. Move Throttle to the “Stop” position.
5. Remove key.
5. Remove key.
SNOW REMOVAL
IMPORTANT: Allow unit and engine to adjust
to the outdoor temperatures before clearing
snow.
NOTE: Attachment clutch should be engaged
before wheel drive clutch when throwing snow.
to the outdoor temperatures before clearing
snow.
NOTE: Attachment clutch should be engaged
before wheel drive clutch when throwing snow.
1. Select Speed Control position and
direction.
2. Engage Attachment Clutch - Right Hand
Lever.
3. Engage Traction Drive Clutch - Left Hand
Lever.
IMPORTANT: DO NOT overload unit capacity
by attempting to clear snow at too fast a rate.
Use slow speed to clear deep or hard packed
snow.
by attempting to clear snow at too fast a rate.
Use slow speed to clear deep or hard packed
snow.
Tips for Operation
Snow is best removed as soon as possible
after snow fall.
To clear an area, run unit in an overlapping
series of paths. For large areas; start in the
middle and throw snow to each side, so snow
is not cleared more than once.
ALWAYS direct snow away from area to be
cleared and with direction of the wind.
after snow fall.
To clear an area, run unit in an overlapping
series of paths. For large areas; start in the
middle and throw snow to each side, so snow
is not cleared more than once.
ALWAYS direct snow away from area to be
cleared and with direction of the wind.
TRAVELING
To travel from one work area to another:
1. Set Throttle to Slow or Part-Throttle
position.
2. Press down on handlebars enough to
raise front of unit slightly off surface.
3. Engage wheel drive clutch without
engaging attachment drive clutch.
TRANSPORT
ALWAYS shut off engine, remove key, and
close fuel shut-off valve when transporting unit
on a truck or trailer.
Use extra care when loading or unloading unit
onto trailer or truck.
Secure unit chassis to transport vehicle.
NEVER secure from rods or linkages that
could be damaged.
DO NOT transport machine while engine is
running.
close fuel shut-off valve when transporting unit
on a truck or trailer.
Use extra care when loading or unloading unit
onto trailer or truck.
Secure unit chassis to transport vehicle.
NEVER secure from rods or linkages that
could be damaged.
DO NOT transport machine while engine is
running.
Ariens Dealers will provide any service or
adjustments which may be required to keep
your unit operating at peak efficiency. Should
engine service be required, contact an Ariens
dealer or an authorized engine manufacturer's
service center.
adjustments which may be required to keep
your unit operating at peak efficiency. Should
engine service be required, contact an Ariens
dealer or an authorized engine manufacturer's
service center.
SERVICE POSITION
Place unit on a flat level surface. Tip unit
forward onto front of impeller housing for
service. Assure unit is secure and will not tip
over. Strap and clamp onto bench if needed.
forward onto front of impeller housing for
service. Assure unit is secure and will not tip
over. Strap and clamp onto bench if needed.
MAINTENANCE
WARNING: AVOID INJURY. Read
and understand the entire Safety
section before proceeding.
and understand the entire Safety
section before proceeding.
WARNING: Before tipping unit up
onto housing, remove fuel so no
spills will occur and remove battery
(if equipped). Ensure unit is secure
and will not tip over during
maintenance.
onto housing, remove fuel so no
spills will occur and remove battery
(if equipped). Ensure unit is secure
and will not tip over during
maintenance.