Maytag bravos w10092823a - sp Manuale Utente

■

■

Are the hot and cold faucets turned on?  

Are the water inlet hoses kinked or clogged? 

Are the water inlet valve screens clear? 

Press POWER/CANCEL to clear display.

■

■

Is the drain hose kinked or clogged? 

Is the drain hose installed properly? See “Connect the  

Drain Hose” in the Installation Instructions.  

Press POWER/CANCEL to clear display.

■

■

If the load is unbalanced, the washer will display this code 

while running an imbalanced load correction routine at the end 

of the wash cycle and before the final spin. If the code remains 

and the wash cycle dial is flashing after the recovery routine 

has stopped, open lid and redistribute the load. Close lid and 

press START/PAUSE.

NOTE: For best performance, load garments in loose heaps 

evenly around the basket wall. Do not load above the stainless 

steel portion of the basket.

■

■

Is the washer overloaded? The washer has attempted to fill 

and begin the wash cycle. If the washer is overloaded, it will 

drain any water and detergent that was added during the fill. To 

correct the overload, remove several items and add detergent. 

Close lid and press START/PAUSE.

■

■

Regular or non-HE hand-washing detergents are not 

recommended for this washer.

Always measure detergent carefully. Follow detergent 

manufacturer’s directions. Remember, concentrated detergents 

such as 2x or higher will use less detergent based on load size.

If excessive suds are detected, the washer will display this code 

while running a suds reduction correction routine at the end 

of the wash cycle. The suds reduction routine removes extra 

suds and assures proper rinsing of your garments. If the code 

remains and the wash cycle dial is flashing after the recovery 

routine has stopped, re-select your desired cycle using cold 

water. Press START/PAUSE. Do not add detergent.

■

■

Is the lid open? Close the lid to clear the display. If the lid 

remains open for more than 10 minutes, water in the wash tub 

will drain.

■

■

This code will appear at the end of the wash cycle to indicate 

that the cold and hot water inlet hoses are switched. See 

“Connect the Inlet Hoses” in the Installation Instructions.

■

■

Indicates lid is not locked. Check for items caught in the lid 

keeping it from closing. Press POWER/CANCEL once to clear 

the code.
    

■

■

Is there excessive weight on the lid, such as a basket of 

laundry? Excessive weight will keep the lid from unlocking. 

Press POWER/CANCEL once to clear the code.

■

■

Press POWER/CANCEL once to clear code. Press START/PAUSE 

to continue cycle. If code appears again, call for service.

■

■

This code will appear when your washer sets back to factory 

default.

To return all options and modifiers to Factory Default, press 

POWER/CANCEL, select Drain & Spin cycle, and then press 

Extra Rinse, Fabric Softener, Extra Rinse, Fabric Softener within 

5 seconds. When done correctly, the 7-segment displays show 

“Fd” for 3 seconds and then unit returns to Standby Mode.

■

■

The washer must be level. The front and rear feet must 

be in firm contact with the floor. Check that the locknuts 

are tightened. See “Level the Washer” in the Installation 

Instructions.
     Is the floor flexing, sagging, or not level?

■

■

Flooring that flexes or is uneven can contribute to noise and 

vibration of the washer. A 

3

⁄

4

" (19 mm) piece of plywood 

under the washer will reduce the sounds. See “Location 

Requirements” in the Installation Instructions.
Is the load balanced?                                                                                      

■

■

Evenly distribute the load in the washer basket and make sure 

the height of the load does not exceed the top row of basket 

holes. See “Starting Your Washer.”
Do you hear clicking or other noises when the cycle changes 

■

■

When the drive system shifts or the washer basket settles 

between cycles, you may hear noises that are different from 

your previous washer. These are normal washer noises.
 Is the washer gurgling or humming?

■

■

When the washer drains, the pump will make a continuous 

humming with periodic gurgling or surging sounds as the final 

amounts of water are removed. This is normal.
Are you washing a small load?

■

■

You will hear more splashing sounds when washing small 

loads. This is normal.
The washer basket moves while washing. 

■

■

This is normal.