Motorola motonav t815 Manuale Utente
15
1. Adhesive: Locate the round adhesive pad. Peel off the backing on one of the adhesive pads
supplied. Attach the adhesive pad to the bottom of the dash mount bracket. Peel off the backing
on the other side of the adhesive pad and firmly stick the dash mount bracket to the dash. For
the strongest signals, choose a spot where the GPS receiver can have a clear view of the sky.
on the other side of the adhesive pad and firmly stick the dash mount bracket to the dash. For
the strongest signals, choose a spot where the GPS receiver can have a clear view of the sky.
2. Velcro: Locate the supplied round Velcro pad. Peel off the protective backing on one side and
stick the pad to the bottom of the dash mount bracket. Remove the remaining protective backing
and stick the Velcro to the desired spot on the dash. To remove the bracket, separate the Velcro
pad.
and stick the Velcro to the desired spot on the dash. To remove the bracket, separate the Velcro
pad.
3. Friction pad: Locate the friction pad, remove the backing, and stick it to the bottom of the dash
mount. The friction pad allows the GPS receiver to sit on the dash without it sliding around.
Visor Mount and Base
Note: The visor mount and base are only available in North America.
The visor mount comes in two pieces and must be assembled. Locate the visor mount and visor mount
base. Align the arrows on both pieces and slide them until they lock. To attach the GPS receiver, position
the GPS receiver per the sketch on the visor base and slide them together. The GPS receiver can easily
be removed by sliding it off of the mounts and lifting off.
base. Align the arrows on both pieces and slide them until they lock. To attach the GPS receiver, position
the GPS receiver per the sketch on the visor base and slide them together. The GPS receiver can easily
be removed by sliding it off of the mounts and lifting off.
Belt Clip
Note: The belt clip for MOTONAV is only available in Europe.
The GPS receiver can easily be snapped into the belt clip for use outside of a vehicle. Make sure the belt
clip is firmly attached to a belt or strap to avoid dropping it.
clip is firmly attached to a belt or strap to avoid dropping it.
Universal Phone Holder (UPH)
The universal phone holder (UPH) is used to hold the phone such that the display is visible to the driver.
It has several ways it can be attached:
It has several ways it can be attached:
1. Gooseneck Mount: The gooseneck mount can be attached to a smooth surface by its suction
cup. Press the suction cup firmly to a smooth surface and push the thumb lever down. Flip the
thumb lever up and pull the tab to release. If needed, the cup can be slightly moistened for better
adhesion. While mostly intended to be mounted to the windshield, a suction cup base is also
provided for mounting the gooseneck to non-smooth surfaces. Locate the suction cup base and
remove the protective covering from the adhesive on the bottom. Press the base firmly down
onto the appropriate location on the dash. The suction cup can then be pressed into the suction
cup base and the lever flipped. Attach the UPH to the other end of the gooseneck by sliding it
over the hooks on the end of the gooseneck.
thumb lever up and pull the tab to release. If needed, the cup can be slightly moistened for better
adhesion. While mostly intended to be mounted to the windshield, a suction cup base is also
provided for mounting the gooseneck to non-smooth surfaces. Locate the suction cup base and
remove the protective covering from the adhesive on the bottom. Press the base firmly down
onto the appropriate location on the dash. The suction cup can then be pressed into the suction
cup base and the lever flipped. Attach the UPH to the other end of the gooseneck by sliding it
over the hooks on the end of the gooseneck.
2. Adhesive mount: Locate the rectangular adhesive patch. Remove the yellow
backing and press it firmly to the back of the UPH. Remove the green backing and
press the UPH to the desired spot on the dash.
press the UPH to the desired spot on the dash.
UPH
Release Tab
Suction Cup
Base