Garmin Striker 7sv Manuale Proprietario

number to display water depth. Enter a 0 in this value to 

display depth below keel and depth below transducer.

Select Settings > My Vessel > Keel Offset.

Select   or   based on the location of the transducer.

Enter the distance measured in step 1.

You can set the temperature offset to compensate for the 

temperature reading from a temperature-capable sensor.

Measure the water temperature using the temperature-

capable transducer that is connected to the device.

Measure the water temperature using a different 

thermometer or temperature sensor that is known to be 

accurate.

Subtract the water temperature measured in step 1 from the 

water temperature measured in step 2.
This is the temperature offset. Enter this value in step 5 as a 

positive number if the sensor connected to the device 

measures the water temperature as being colder than it 

actually is. Enter this value in step 5 as a negative number if 

the sensor connected to the device measures the water 

temperature as being warmer than it actually is.

Select Settings > My Vessel > Temp. Offset.

Use the arrow keys to enter water temperature offset 

measured in step 3.

Select Settings > Alarms > Navigation.
Arrival: Sets an alarm to sound when you are within a specified 

distance or time from a turn or a destination.

Anchor Drag: Sets an alarm to sound when you exceed a 

specified drift distance while anchored.

Off Course: Sets an alarm to sound when you are off course by 

a specified distance.

Alarm Clock: Sets an alarm clock.
Device Voltage: Sets an alarm to sound when the battery 

reaches a specified low voltage.

GPS Accuracy: Sets an alarm to sound when the GPS location 

accuracy falls outside the user-defined value.

Select Settings > Alarms > Sonar.
Shallow Water: Sounds when the water depth is shallower than 

the specified depth.

Deep Water: Sounds when the water depth is deeper than the 

specified depth.

Water Temp.: Sounds when the water temperature varies more 

than ± 2°F (± 1.1°C). Alarm settings are saved when the 

device is turned off.
NOTE: You must connect the device to a temperature-

capable transducer to use this alarm.

Fish: Sets an alarm to sound when the device detects a 

suspended target.
•

 sets the alarm to sound when fish of all sizes are 

detected.

•

 sets the alarm to sound only when medium or large 

fish are detected.

•

 sets the alarm to sound only when large fish are 

detected.

Select Settings > Units.
System Units: Sets the unit format for the device.
Variance: Sets the magnetic declination, the angle between 

magnetic north and true north, for your present location.

North Reference: Sets the direction references used in 

calculating heading information. True sets geographic north 

as the north reference. Grid sets grid north as the north 

reference (000º). Magnetic sets the magnetic north as the 

north reference.

Position Format: Sets the position format in which a given 

location reading appears. Do not change this setting unless 

you are using a map or chart that specifies a different 

position format.

Map Datum: Sets the coordinate system on which the map is 

structured. Do not change this setting unless you are using a 

map or chart that specifies a different map datum.

Time Format: Sets a 12-hour, 24-hour, or UTC time format.
Time Zone: Sets the time zone.
Daylight Savings Time: Sets daylight savings time to Off or On.

NOTE: Some settings and options require additional hardware.
Select Settings > Navigation.
Route Labels: Sets the type of labels shown with route turns on 

the map.

Turn Transition Activ.: Sets the turn transition to be calculated 

based on time or distance.

Turn Transition Time: Sets how many minutes before the turn 

that you transition to it as the next leg, when Time is selected 

for the Turn Transition Activ. setting.

Turn Transition Dist.: Sets how far before the turn that you 

transition to it as the next leg, when Distance is selected for 

the Turn Transition Activ. setting.

Route Start: Selects a starting point for route navigation. You 

can select Boat to start navigation from the current vessel 

location, or Waypoints to start from the first waypoint on the 

route.

NOTE: This deletes all settings information you have entered.

Select 

 > System > System Information > Factory 

Settings.

Select an option.

8

Device Configuration