Budderfly LLC R0610400 Manuale Utente
Part No R0610401
Description:
Installing a Budderfly adapter transforms your building’s existing wiring into the “Budderfly Open Network” and allows
the adapter to monitor energy consumption and communicate the data to a facility controller.
Budderfly adaptors use the existing power line for communication and thus require no re‐wiring.
Using our Budderfly software, you can visualize consumption data and manage each individual adapter.
As a component of Budderfly system, the Budderfly Controllable Outlet is designed to work with all other Budderfly
adapters. It is a plug‐and‐play replacement for your existing duplex outlet, and it provides control on one of its two
sockets. Once installed, The Budderfly Controllable Outlet also acts as a repeater to extend the range of the network and
increase efficiency.
the adapter to monitor energy consumption and communicate the data to a facility controller.
Budderfly adaptors use the existing power line for communication and thus require no re‐wiring.
Using our Budderfly software, you can visualize consumption data and manage each individual adapter.
As a component of Budderfly system, the Budderfly Controllable Outlet is designed to work with all other Budderfly
adapters. It is a plug‐and‐play replacement for your existing duplex outlet, and it provides control on one of its two
sockets. Once installed, The Budderfly Controllable Outlet also acts as a repeater to extend the range of the network and
increase efficiency.
Installation:
The Budderfly Controllable Outlet may be used in new installations or to replace an existing Outlet. The wiring schematic will be as per below:
1. At the circuit breaker or fuse panel, disconnect the power for all of the
circuits in the switch junction box.
2. Double Check that the power is OFF to the Outlet by trying to turn on a
device connected to the plug before continuing.
3. Remove the wall plate from the outletyou are replacing. Then, unscrew the
outlet itself and pull it out from the junction box.
4. Disconnect the wires from the outlet you are replacing.
5. Follow the Wiring information provided below and connect the wires as
5. Follow the Wiring information provided below and connect the wires as
follows:
‐ Connect the GROUND wire (usually Bare Copper or Green) to the Ground
wire of Budderfly Controllable Outlet (Yellow & Green).
‐ Connect the LINE wire (usually Black) that comes from the electrical service
panel to the HOT wire of Budderfly Controllable Outlet (Black).
‐ Connect the NEUTRAL wire (usually White) to the Neutral wire of Budderfly
Controllable Outlet (White).
6. After you have connected all of the wires, ensure that all of the wire
connectors are firmly attached and that there is no exposed copper except
for the GROUND wire.
for the GROUND wire.
7. Gently place Budderfly Controllable Outlet into the junction box. Then,
screw the Outlet into place.
8. Reinstall the wall plate
9. Enable power to the Outlet from the circuit breaker or fuse panel
10. Add the device address to the Budderfly software.
9. Enable power to the Outlet from the circuit breaker or fuse panel
10. Add the device address to the Budderfly software.
WARNING: If you are not sure about any part of the above instructions,
consult a qualified electrician.
consult a qualified electrician.
WARNING –ELECTRICAL SHOCK HAZARD
•
The Budderfly Controllable Outlet is intended for installation in accordance with the
National Electric Code and local regulations in the United States.
National Electric Code and local regulations in the United States.
•
If you are not knowledgeable or comfortable with electrical circuitry, you should have a
qualified electrician install the Budderfly Controllable Outlet for you.
qualified electrician install the Budderfly Controllable Outlet for you.
Warning
•
Install the Budderfly Controllable Outlets indoor only.
•
Never use the Budderfly Outlets to power medical and/or life support equipment.
WARNING –ELECTRICAL SHOCK HAZARD
•
Turn OFF the power to the branch circuit for the Outlet at the
service panel.
service panel.
•
All wiring connections must be made with the POWER OFF to
avoid personal injury and/or damage to the Outlet.
avoid personal injury and/or damage to the Outlet.
Wiring Information
•
Important: Budderfly Controllable Outlet is rated for and
intended to only be used with copper wire.
intended to only be used with copper wire.
•
Use 12 AWG or larger wires suitable for 80
o.
•
Remove 3/4" (1.9 cm) of insulation from each wire.
Connect as follows: Twist strands of each end tightly together. Hold
bare ends of wires together and push firmly into wire Nut. Screw Nut
clockwise making sure that no bare conductor shows below the
connector
bare ends of wires together and push firmly into wire Nut. Screw Nut
clockwise making sure that no bare conductor shows below the
connector