Tranzeo Wireless Technologies Inc GNVPZ1NT3 Manuale Utente
Chapter 11: Ethernet Interface Configuration
TR0153 Rev. E1
78
11.1.2
Ethernet Interface IP Configuration
The EnRoute500’s Ethernet interface IP configuration can be changed directly when it is in
repeater mode and using the explicit addressing scheme. It should not be changed directly
when the device is in repeater mode and using the implicit addressing scheme.
When an EnRoute500 is configured to use the implicit addressing scheme, set the IP address
to the desired value by modifying the node ID, mesh ID, and LAN prefix parameters (see
sections 8.3 and 9.1.1). Set the netmask by changing the client address space segments as
described in 9.1.2.
When using the explicit addressing scheme, the IP configuration can be set directly. Care must
be taken to avoid using the same or overlapping address spaces on different devices in a
mesh neighborhood.
repeater mode and using the explicit addressing scheme. It should not be changed directly
when the device is in repeater mode and using the implicit addressing scheme.
When an EnRoute500 is configured to use the implicit addressing scheme, set the IP address
to the desired value by modifying the node ID, mesh ID, and LAN prefix parameters (see
sections 8.3 and 9.1.1). Set the netmask by changing the client address space segments as
described in 9.1.2.
When using the explicit addressing scheme, the IP configuration can be set directly. Care must
be taken to avoid using the same or overlapping address spaces on different devices in a
mesh neighborhood.
CLI
You can view the IP settings for the Ethernet interface with the ‘ip.*’ parameters in the ‘eth0’
interface as shown in the example below.
interface as shown in the example below.
> use eth0
eth0> get ip.*
ip.address = 10.2.4.225 [read-only]
ip.address_force =
ip.broadcast = 10.2.4.255 [read-only]
ip.broadcast_force =
ip.gateway = [read-only]
ip.gateway_force =
ip.netmask = 255.255.255.0 [read-only]
ip.netmask_force =
ip.implicit.size.actual = [read-only]
ip.implicit.size.requested = 31
ip.implicit.start.actual = [read-only]
ip.implicit.start.requested = 225
eth0> get ip.*
ip.address = 10.2.4.225 [read-only]
ip.address_force =
ip.broadcast = 10.2.4.255 [read-only]
ip.broadcast_force =
ip.gateway = [read-only]
ip.gateway_force =
ip.netmask = 255.255.255.0 [read-only]
ip.netmask_force =
ip.implicit.size.actual = [read-only]
ip.implicit.size.requested = 31
ip.implicit.start.actual = [read-only]
ip.implicit.start.requested = 225
When an EnRoute500 is in repeater mode and using the implicit addressing scheme, the
Ethernet IP settings can be changed by altering the ‘id.node’, ‘id.mesh’, and ‘id.lanprefix’
parameters in the ‘sys’ interface and the ‘ip.implicit.start.requested’ parameter in the ‘eth0’
interface.
When an EnRoute500 is configured as a repeater, but is using the explicit addressing scheme,
the IP address, netmask, gateway address, and broadcast address can be set using the
‘ip.address_force’, ‘ip.netmask_force’, ‘ip.gateway_force’, and ‘ip.broadcast_force’ parameters
in the ‘eth0’ interface as shown in the example below.
> use eth0
eth0> set ip.address_force= 10.12.7.1
ip.broadcast_force= 10.12.7.255
ip.gateway_force=
eth0> set ip.address_force= 10.12.7.1
ip.broadcast_force= 10.12.7.255
ip.gateway_force=