Turn off the computer’s power before connecting the base, then
power up the computer once the base is fully connected. When the
base is connected and powered up, put the scanner in the base to
establish a link. The green LED on the base flashes to indicate the
scanner’s battery is charging.

Power Supply Assembly (if included)

Note: The power supply must be ordered separately, if needed.

USB Connection:

Keyboard Wedge Connection:

RS232 Serial Port Connection:

RS485 Connection:

Reading Techniques

The view finder projects an aiming
beam that should be centered over
the bar code, but it can be
positioned in any direction for a
good read.

Hold the scanner over the bar code,
pull the trigger, and center the
aiming beam on the bar code.

The aiming beam is smaller when
the scanner is closer to the code and larger when it is farther from the
code. Hold the scanner close to smaller bar codes, and farther away
from large bar codes to get a proper read.

If the bar code is highly reflective (e.g., laminated), you may need to
tilt the scanner at an angle so the bar code can be scanned.

Note: If the scanner razzes when scanning a bar code, the link has

not been established. If the scanner beeps once, the link has
been established.

Standard Product Defaults

The following bar code resets all standard product default settings.

Note: PDF and 2D bar codes can only be read by Voyager model

1452g2D and cannot be read by model 1452g1D.

Standard Product Defaults

RS485 Interface

The RS485 interface defaults to port 5B. If you have an IBM POS
terminal using port 9B, scan the appropriate code below to program
the terminal, then power cycle the cash register.

Note: For additional RS485 interface selections, see the User’s

Guide for your product at our website,

www.honeywellaidc.com.

USB Serial

Scan the following code to program the scanner to emulate a regular
RS232-based COM Port. If you are using a Microsoft® Windows®
PC, you will need to download a driver from the Honeywell website

(www.honeywellaidc.com)

. The driver will use the next available

COM Port number. Apple® Macintosh computers recognize the
scanner as a USB CDC class device and automatically use a class
driver.

Note: No extra configuration (e.g., baud rate) is necessary.

IBM Port 9B HHBCR-1

Interface

IBM Port 9B HHBCR-2

Interface

USB Serial

USB PC Keyboard

Scan the following code to program the scanner for a USB PC
Keyboard.

Keyboard Country

Scan the Program Keyboard Country bar code below, then scan
the numeric bar code(s) from

page 2

, then the Save bar code to

program the keyboard for your country. As a general rule, the
following characters are not supported by the scanner for countries
other than the United States:
@ | $ # { } [ ] = / ‘ \ < > ~

Note: For a complete list of country codes, see the User’s Guide for

your product at our website,

www.honeywellaidc.com.

Country Code

Scan

Country Code

Scan

Belgium

Italy

Denmark

Norway

Finland

Spain

France

Switzerland

Germany/Austria

USA (Default)

Great Britain

USB PC Keyboard

Program Keyboard Country

Save

Locked Link

If you link a scanner to a base using the Locked Link Mode, other
scanners are blocked from being linked if they are inadvertently
placed into the base. If you do place a different scanner into the
base, it will charge the scanner, but the scanner will not be linked.

To use a different scanner, you need to unlink the original scanner by
scanning the Unlink Scanner bar code.

Override Locked Scanner

If you need to replace a broken or lost scanner that is linked to a
base, scan the Override Locked Scanner bar code with a new
scanner, and place that scanner in the base. The locked link will be
overridden; the broken or lost scanner’s link with the base will be
removed, and the new scanner will be linked.

Unlinking the Scanner

If the base has a scanner linked to it, that scanner must be unlinked
before a new scanner can be linked. Once the previous scanner is
unlinked, it will no longer communicate with the base. Scan the
Unlink Scanner bar code to unlink a scanner.

Locked Link Mode

(Single Scanner)

Override Locked Scanner

Unlink Scanner