HID Global Corporation SMARTID Manuale Utente
Page 18 of 19
February 13, 2008
© 2008 HID Global Corporation. All rights reserved.
SmartID Proximity Reader - 8030-901, Rev A.0
6.5 DGT/NCC
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變
更頻率、加大功率或變更原設計之特性及功能。低功率射頻電機之使用不得影響飛
航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方
得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機
須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
更頻率、加大功率或變更原設計之特性及功能。低功率射頻電機之使用不得影響飛
航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方
得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機
須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
According to "Administrative Regulations on Low Power Radio Waves Radiated
Devices" Without permission granted by the DGT, any company, enterprise, or
user is not allowed to change frequency, enhance transmitting power or alter
original characteristic as well as performance to a approved low power radio-
frequency devices. The low power radio-frequency devices shall not influence
aircraft security and interfere legal communications; If found, the user shall cease
operating immediately until no interference is achieved. The said legal
communications means radio communications is operated in compliance with the
Telecommunications Act. The low power radio-frequency devices must be
susceptible with the interference from legal communications or ISM radio wave
radiated devices.
Devices" Without permission granted by the DGT, any company, enterprise, or
user is not allowed to change frequency, enhance transmitting power or alter
original characteristic as well as performance to a approved low power radio-
frequency devices. The low power radio-frequency devices shall not influence
aircraft security and interfere legal communications; If found, the user shall cease
operating immediately until no interference is achieved. The said legal
communications means radio communications is operated in compliance with the
Telecommunications Act. The low power radio-frequency devices must be
susceptible with the interference from legal communications or ISM radio wave
radiated devices.
February 13, 2008
© 2008 HID Global Corporation. All rights rese
SmartID Proximity Reader - 8030-901, Rev A.0
Contents
1
Products List...................................................................
2
Overview .........................................................................
2.1
Mullion Mounting..................................................
2.2
Indications ...........................................................
2.3
Connections.........................................................
2.4
Output Protocols ..................................................
2.5
Security................................................................
3
Specifications .................................................................
4
Timing..............................................................................
5
Installation Instructions .................................................
5.1
Wall Mounting Drawing (All Models) ....................
5.2
Conductor Connections (All Models) ...................
5.3
Tamper Switch - Optional ....................................
5.4
Switch Box Mounting Plate - Optional..................
5.5
Mullion Reader Mounting Plate – Spacer ............
6
Regulatory.......................................................................
6.1
UL ........................................................................
6.2
FCC / Canada Radio Certification........................
6.3
CE Marking ..........................................................
6.4
Asia and Pacific Rim............................................
6.5
DGT/NCC ............................................................
7
Contacts ..........................................................................
List of Figures
Figure 1 Mullion Mounting .............................................................
Figure 2 Tamper Switch ................................................................
Figure 3 Mounting Plate Step 1 and 2 ...........................................
Figure 4 Mounting Plate Step 3 and 4 ...........................................
Figure 5 Mounting Plate Spacer ....................................................
Figure 2 Tamper Switch ................................................................
Figure 3 Mounting Plate Step 1 and 2 ...........................................
Figure 4 Mounting Plate Step 3 and 4 ...........................................
Figure 5 Mounting Plate Spacer ....................................................